Manual Ariston CP 058 MT.2 S (page 25 of 72) (English, French, Italian, Portuguese, Spanish)

507044

Zoom out

Zoom in

1/72

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated by the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only.

! The manufacturer declines any liability should these

safety measures not be observed.

Replacing the cable

Use a rubber cable of the type H05VV-F with a cross section

of 3 x 1.5 mm².

The yellow-green earth wire must be 2 ÷ 3 cm longer than

the other wires.

Gas connection

Connection to the gas network or to the gas cylinder

may be carried out using a exible rubber or steel hose,

in accordance with current national legislation and after

making sure that the appliance is suited to the type of gas

with which it will be supplied (see the rating sticker on the

cover: if this is not the case see below). When using liquid

gas from a cylinder, install a pressure regulator which

complies with current national regulations.

! Make sure that the gas supply pressure is consistent

with the values indicated in the Table of burner and nozzle

specifications (see below). This will ensure the safe

operation and durability of your appliance while maintaining

efcient energy consumption.

Gas connection using a exible rubber hose

Make sure that the hose complies with current national

legislation. The internal diameter of the hose must measure: 8

mm for a liquid gas supply;13 mm for a methane gas supply.

Once the connection has been performed, make sure that

the hose:

• Does not come into contact with any parts which reach

temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and that it

is not kinked or bent.

• Does not come into contact with blades, sharp corners

or moving parts and that it is not compressed.

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits rmly into place at both ends, where it will be xed

using clamps which comply with current regulations.

! If one or more of these conditions is not fullled or if the

cooker must be installed according to the conditions listed

for class 2 - subclass 1 appliances (installed between two

cupboards), the exible steel hose must be used instead

(see below).

Connecting a exible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with current

national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose length

does not exceed a maximum of 2 metres, making sure that

the hose is not compressed and does not come into contact

with moving parts.

Checking the connection for leaks

When the installation process is complete, check the hose

ttings for leaks using a soapy solution. Never use a ame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).

Adapting the hob

Replacing the nozzles for the hob

burners:

1. Remove the hob grids and slide

the burners off their seats.

2. Unscrew the nozzles using a 7

mm socket spanner (see gure), and

replace them with nozzles suited to

the new type of gas (see Burner and

nozzle specications table).

3. Replace all the components by following the above

instructions in reverse.

Replacing the nozzles on separate “double ame “

burners

1. remove the grids and slide the burners from their

housings. The burner consists of 2 separate parts (see

gure);

2. unscrew the burers with a 7 mm wrench spanner. The

internal burner has a nozzle, the external burner has

two (of the same size). Replace the nozzle with models

suited to the new type of gas (see table 1).

3. replace all the components by repeating the steps in

reverse order.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston CP 058 MT.2 S in the language / languages: English, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 23,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston CP 058 MT.2 S Manual

Product: