719964
17
Zoom out
Zoom in
Previous page
1/64
Next page
/ 17
INSTALLATION
Warning
The exhaust gas ducts must not be in contact with or close to
inflammable material and must not pass through building structures
or walls made of inflammable material.
When replacing an old appliance, the flue system must be changed.
Important
Ensure that the flue is not blocked.
Ensure that the flue is supported and assembled in accordance with
these instructions.
150 mm
118
* Min slope: 1˚
1˚= 17.5mm per metre
150 mm
* pente
Installation without extension
Installation with extension
Level
Level
Fitting the Coaxial Flue (Ø 60 / 100 Horizontal)
Contents:
1x Silicone O-Ring (60mm)
1x Elbow (90°)
2x Wall Seals (Internal & External)
1x Flue Pipe including Terminal (1 metre - 60/100)
2x Flue Clamps
4x Screws
2x Seals
Once the boiler has been positioned on the wall, fit the rubber flue
seal into the internal flue turret (see diagram opposite),
Insert the elbow into the socket and rotate to the required position.
note: It is possible to rotate the elbow 360° on its vertical axis.
Using the flue clamp, seals and screws supplied (Fig 4) secure the
elbow to the boiler.
The 1 metre horizontal flue kit (3318073) supplied is suitable for an
exact X dimension of 753mm.
Measure the distance from the face of the external wall to the face
of the flue elbow (X - Fig 2), this figure must now be subtracted from
753mm, you now have the total amount to be cut from the plain
end of the flue.
Draw a circle around the outer flue and cut the flue to the required
length taking care not to cut the inner flue, next cut the inner
flue ensuring that the length between the inner and outer flue is
maintained. (Fig 4).
e.g.
X = 555mm
753-555 = 198mm (Length to be cut from the plain end of the
flue).
Once cut to the required length, ensure that the flue is free from
burrs and reassemble the flue. If fitting the flue from inside of the
building attach the outer wall seal to the flue terminal and push
the flue through the hole, once the wall seal has passed through
the hole, pull the flue back until the seal is flush with the wall.
Alternatively, the flue can be installed from outside of the building,
the outer seal being fitted last.
Should the flue require extending, the flue connections are push fit,
however, one flue bracket should be used to secure each metre of
flue.
Note: See table for maximum and minimum flue runs.
slope
Fig. 3
Note: A Plume management kit is available for 60/100 horizontal
termination. Instructions for installation are supplied with the
Plume management kit.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston Clas HE R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston Clas HE R in the language / languages: English as an attachment in your email.

The manual is 16,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info