47703

Ariston CD12T Manual

11
Zoom out
Zoom in
Previous page
1/14
Next page
10
GB
Transit packing
After removing the packing, check the appliance for damage.
If you have any doubts do not use the washer and call a
qualified technician. Keep the packaging components (plastic
bags, polyester foam, nails etc.) out of the reach of children
since they could be dangerous. The interior of the washer-
dryer, has an oscillating unit which is fixed on the back by 3
screws during transport (figure 3). Before starting up the
washer-dryer, release the unit, by unscrewing the 3 screws.
Seal the screw holes with the plastic plugs supplied with the
appliance.
Levelling
The machine must be level in order to operate properly, To
level the machine, simply regulate the adjustable feet (fig. 4);
the angle of inclination (measured on the top of the machine)
must not exceed 2 degrees. If the washer-dryer is installed on
a carpeted floor, check that there is sufficient ventilation space
between the floor and the bottom of the machine.
Water supply
Both hot and cold water supplies are preferable and they
should be between 34.5kN/m²(5lb/in²) and 1034.2kN/m²
(150lb/in²) pressure. The hose having the red end fitting
should be encountered between the hot supply and the
threaded connection adjacent to the letter H on the rear of
the machine. The hose having the white end fittings should
be connected between the cold supply and the threaded
connection adjacent to the letter C on the rear of the ma-
chine (see fig. 5). Remember to insert a sealing washer at
each connection to ensure watertight joints. Do not
overtighten the connections by using tools -hand tight is
sufficient to prevent leaks. It is generally more convenient to
have these supplies away from the sink taps. Where no
suitable hot water supply is available or it does not meet
these requirements, both inlet hoses may be connected to a
cold supply by using two taps etc., or a «T» junction on the
plumbing (see fig. 6) however, use of cold water only will
increase programme times.
Note: the maximum temperature should not exceed 70°C
(158°F).
Installation
Fig. 5 Fig. 6
Connecting the drain pipe
Connect the drain hose to a drain (with a minimum inner
diameter of 4 cm), avoiding excessive crimping or the
formation of elbows. It is important that the hose be
positioned at a height greater than 60 cm. If this is not the
case, the hose must be fastened to the hook located on the
top part of the back of the machine (fig. 7).
If a drain pipe coming from the wall is used to connect the
hose, have a qualified plumber/technician check to make
sure that it functions properly. If your home is on the top of
an apartment building or condominium, the drain may be
subject to a siphoning effect which results in the machine
filling and draining continuously. To eliminate this
inconvenience, special valves are available on the market
which can be fitted to the drain hose.
Fig. 3
Fig. 4
Fig. 7
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston CD12T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston CD12T in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info