454579
6
Zoom out
Zoom in
Previous page
1/17
Next page
17
GB
How to Start the Appliance
NOTICE
After the appliance has been delivered, stand it in the
upright position and wait approximately 3 hours be-
fore connecting it to the electrical outlet to guarantee
that it operates properly.
Before placing foodstuffs in the refrigerator or freezer, clean
the interior well with warm water and baking soda.
Motor protection delay
This model is provided with a motor protection control
system. Therefore, if the compressor does not start
immediately upon installation, do not worry as it will
start automatically after approximately 8 minutes.
This is also what will happen every time the power
supply is interrupted, both due to a power failure or
should you switch it off yourself (to clean or defrost
your freezer, for example).
After plugging the appliance into a suitable electricity
socket, ensure the display is on with the “OFF” words in
the indication spaces concerning the two compartments
(fridge and freezer).
Freezer compartment
When the appliance is switched on (by pressing the ON/
OFF button “A” for more than two seconds), the freezer
compartment is automatically brought to the standard setting
of - 18°C. We recommend you enable the SUPER FREEZE
function to speed up the cooling process of the compartment;
when the latter has reached its optimal temperature, the
function shall be automatically disabled and you may place
your frozen food inside the compartment.
Refrig ompartment
When the appliance is switched on, the refrigerator
compartment turns on automatically, and it is brought to the
standard setting of + 5°C. We recommend you enable the
SUPER COOL function to speed up the cooling process of
the compartment: after a few hours, you may place food inside
the refrigerator.
How to use the display
Firstly, take all the advice that appears in the form of scrolling
text on the display: it will be of use to you, especially when
you make your first settings.
Temperature settings:
If the compartment concerned is switched off, the word OFF
will appear on the relative indication space on the display (G for
the refrigerator and H for the freezer). If the compartment is
switched on, then the temperature set at that time will appear.
To change it, press the MODE (D) button as many times as
necessary for the figure corresponding to the temperature set to
flash in the relative indication space. Now you can select the
new temperature to set by pressing the ADJUST/SELECT + (E)
(to increase the temperature displayed by one degree) and/or
ADJUST/SELECT - (F) (to decrease the temperature displayed
by one degree) buttons. Once you have reached the desired
temperature, you should set it by pressing the MODE (D) button
again to confirm the selection. Now the new temperature will
stop flashing and will remain fixed in the relevant indication space
on the display to indicate that the new setting has been made.
NOTE: if you do not confirm your selection by pressing the
MODE button within ten seconds of the last action
performed on the display, the latter shall go back to displaying
the temperature previously in being and indicate that no
new temperature has been set.
The temperatures set automatically are +5°C for the refrigerator
compartment and -18°C for the freezer compartment and these
are the standard temperatures for food storage.
The settable temperatures for the refrigerator compartment
range from +2°C to +8°C, whereas those for the freezer
compartment range from -18°C to -26°C. When the ECO
function is enabled, the possible settings are instead closer
to the standard ones for food storage: from +4°C to +6°C
for the refrigerator compartment and from -18°C to -20°C
for the freezer compartment. The possible increases and
decrease are still of 1°C.
When the HOLIDAY function is enabled, temperature
regulations cannot be made, but the appliance automatically
sets itself to the best setting for the situation: +12°C for the
refrigerator compartment (if enabled) and -18°C for the
freezer compartment.
How to use the functions:
ECO
ECO
ECO
Function symbol in normal operating conditions
(only green symbol lit)
Function selected (green symbol and red outline
lit)
Function enabled (green symbol and blue
background lit)
Press the MODE (D) button as many times as necessary for
the red outline of the function you wish to act on to light
up: this indicates that the function has been selected and is
ready to be enabled or disabled. Now you can act on the
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston BCO-M40 IX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston BCO-M40 IX in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info