44198

Ariston AWD121 Manual

7
Zoom out
Zoom in
Previous page
1/60
Next page
Instructions for installation and use
www.aristonappliances.us
You should carefully position the drain hose to avoid kinks and
ensure proper drainage of the water.
The outlet end of the drain hose must be at least 25” (62 cm)
above the base of the machine. At this point it is possible for
the water to be discharged into a sink or drain pipe, but an air
break must be available at this 24” height to prevent the machine
from syphoning (see fig. aside).
No more than 6” of the drain hose should be inserted in the
drain pipe.
IMPORTANT
make sure that the drain hose is not kinked and the water flow
has not been restricted.
Standpipe drain system:
In RV installation needs a 1-1/2 inch (3.7 cm) diam.
standpipe with minimum carry away capacity of 7 gallons (31
liters) per minute or 2” (5 cm) in home installation.
Floor Standpipe drain:
Top of standpipe must be at least 25 inches (62 cm) high and
no higher than 34 inches (86 cm) from the bottom of
washer (A).
Wall standpipe drain:
25 inches (62 cm) min.; 34 inches (86 cm.) max
from end of drain hose to bottom of washer (B).
PLUMBING (Water Out)
25
2
25”
34”
Included in the accessories supplied with this machine are 2
inlet hoses and 4 rubber washers. The straight end of these
hoses should be connected to the supply fig. 1.
The 90° angled end of these hoses should be connected to
the inlet valves on the back of the machine, using one of the
washers to make a water tight seal on each connection.
The couplings should be tightened by hand, a tool should only
be used if a leak occurs. Do not use excessive force (see M,
fig. 1).
The DO NOT USE AN EXTENSION CORD.
Repair or replacement of a part should be made only by a
qualified service technician to prevent personal injury or damage
to the machine. inlet valves are color coded:
Red = Hot
White = Cold
PLUMBING (Water Inlet)
Connection to the water mains
Water pressure must range within the values indicated on the
data plate on the rear of your washer-dryer. If the water pipes are
new or left unused, then before connecting the machine run the
water until clear to remove debris. Connect the inlet hose to a
cold water tap having a ¾“ BSP thread. Ensure that there are
rubber washers are at each end of the inlet hose. The L-Shaped
end goes on the machine and straight ends on the water faucets
Note: Replace inlet hoses after 5 years of use to reduce the
risk of hose failure. Record hose installation or replacement
dates on the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear or leaks are found.
Fig. 1 - Water pipe inlet at the top right
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston AWD121 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston AWD121 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 10,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info