47691
20
Zoom out
Zoom in
Previous page
1/24
Next page
20
NA
Troubleshooting
Possible causes / Solutions:
The plug has not been inserted into the electrical socket, or it has
not been inserted far enough to make contact.
There is no power in the house.
The porthole door has not been shut properly.
The START/RESET button has not been pressed.
The water tap has not been turned on.
The water inlet hose is not connected to the tap.
The hose is kinked.
The water tap has not been turned on.
There is no water in the house.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The end of the outlet hose has not been fitted at a height between
25 - 34 inches (62 and 86 cm) from the floor (see Installation).
The free end of the hose is underwater (see Installation).
If If the dwelling is on one of the upper floors of a building, there
may be problems relating to water drainage, causing the washing
machine to load and drain water continuously. Special anti-
draining valves are available in shops and help to avoid this
inconvenience.
The water drainage system is not fitted with a breather pipe.
The programme does not include a draining phase: some
programs require manual draining (see Programmes and
options).
The Easy Iron option is enabled: to complete the program, press
the START/RESET button (see Programs and options).
The outlet hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked properly when the appliance was
installed. Remove shipping bolts (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and a wall
(see Installation).
The load is not balanced properly (see Operating the washing
machine).
The water inlet hose is not screwed on to the tap correctly (see
Installation).
The detergent dispenser drawer is blocked (for instructions on
how to clean it, see Care and maintenance).
The outlet hose has not been secured properly (see
Installation).
Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
Malfunction:
The washing machine will not switch on.
The wash cycle does not begin.
The washing machines fails to fill with
water.
The machine continuously fills and
drains water.
The machine does not drain or spin.
The washing machine vibrates too much
during the spin cycle.
The washing machine leaks.
The icons corresponding to the Phase in
progress flash rapidly at the same time
as the ON/OFF indicator light.
From time to time your machine may not operate as it should. Before calling for Assistance (see Service-Assistance),
make sure that the problem cannot be resolved easily using the following list.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston AW129 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston AW129 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info