543353
6
Zoom out
Zoom in
Previous page
1/23
Next page
6
NA
www.aristonappliances.us
Remove the Shipping Bolts
IMPORTANT:
Read these instructions to remove
the 4 shipping bolts (see
Description for location). Situated
on one either side of the rear
panel, All shipping bolts MUST
be removed before use.
! Failure to do so may cause
damage to your machine.
It is important the transit bolt and
spacer (see pic) come out intact.
1. Unscrew the bolt using a 13
mm wrench.
2.
STOP when 3 threads can be
seen.
3. Hold, slide sideways and pull to
remove.
4. For safety, close the
holes left by removing the bolts.
Location
Where you install your machine will affect its performance:
! For your safety and to comply with electrical
regulations, seek professional advice if you want to install
your machine in a bath or shower room.
Make sure that the electrical socket and water taps are
easily accessible. You should switch off the machine's
electrical and water supplies when you are not using
it for extended periods.
Make sure that you allow enough space for the
machine. Select a space at least 23.6 (60 cm) wide,
23.6 (60 cm) deep and 33.4 (85 cm) high. Also
leave enough space to open the door fully, so that you
can load and unload it easily.
Where possible, the machine should be positioned on
a solid floor to minimise vibration.
Take care when you move the machine not to rip any
floor coverings. The weight of the machine may cause
indentations in some floor coverings.
Levelling
Your machine will be noisy if the two front feet are not
adjusted so that the machine stands firm and level.
! The machine should be levelled from side to side and
from front to back.
1. Move your machine into its final location.
- Take care not to trap or kink the hoses.
2. Turn one or both front feet counter-clockwise by hand
until the feet cannot be turned any more.
When adjusting the feet, use a spirit level to check the
machine stands level, from side to side and from front to
back.
If the floor is not perfectly level,
compensate for any unevenness
by tightening or loosening the
adjustable front feet (see figure);
the angle of inclination, measured
according to the worktop, must not
exceed 2°.
The spring on each foot will stop
them coming loose.
! If it is placed on a fitted or loose carpet, adjust the feet in
such a way as to allow enough room for ventilation beneath
the machine.
Did you know?
the shipping bolts are fitted to ensure that your machine is undamaged during delivery.
...both of the shipping bolts must be removed before using the machine, not doing so will lead to
excessive vibration, movement of the machine and could eventually lead to internal damage.
...the majority of problems with noisy machines are due to the shipping bolts not being removed,
closely followed by the feet not being adjusted correctly to level the machine.
...you will be charged for a service engineers visit if a problem with your machine is caused by
incorrect installation or misuse.
! Packaging materials are
not children's toys.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston AW 125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston AW 125 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info