719940
10
Zoom out
Zoom in
Previous page
1/24
Next page
10 /
USER’S MANUAL
Appliance shut-off conditions
The boiler is protected from malfunctions by means of internal checks
performed by the electronic P.C.B., which stops the boiler from operating
if necessary. In the event of the boiler being shut off in this manner, a
code appears on the control panel display which refers to the type of
shut-off and the reason behind it.
Two types of shut-off may occu
r:
Safety shut-off
This type of error is “volatile”, which means that the boiler starts up
again automatically as soon as the problem which caused the shut-off
is removed.
The display shows the code and the error description.
Fault 110 - SendProbeDamaged
In fact, soon as the cause of the shut-off disappears, the boiler starts up
again and continues to operate normally.
If the boiler still indicates a safety shut-off, switch it off. Make sure the
external electric switch is in the OFF position, shut off the gas valve and
contact a qualied technician.
Safety shut-off due to insufcient water pressure
In caso di insufciente pressione dell’acqua nel circuito riscaldamento
la caldaia segnala un arresto di sicurezza.
The display shows
Fault 108 - FillingNeeded.
The system may be restarted, re-balancing the water pressure, by
using the filling procedure - see note 1.
If the re-balancing request is performed on a frequent basis, switch
the boiler off, bring the external electric switch to the OFF position,
shut off the gas valve and contact a qualified technician to check for
any leaks of water.
Operation shutdown
This type of error is “non-volatile”, which means that it is not removed
automatically.
The display shows the code and the error description.
To restore normal operation press the RESET button on the control
panel.
The dispay shows
“Resetinprogress”
and then
“Faultsolved”.
If the problem manifests itself again after several attempts to reset the
appliance, contact a qualied technician.
Fault 108
Filling Needed
ALERT
Fault 110
Send Probe Damaged
ALERT
Fault 501
No flame detected
Press the Reset button
ALERT
Reset in corso
Fault solved
Fault 501
No flame detected
Press the Reset button
ALERT
Important
If this shutdown occurs frequently, contact an authorised Technical
Service Centre for assistance. For safety reasons, the boiler will permit
a maximum of 5 resets in 15 minutes (5 presses of the RESET button);
at the 6th attempt within this 15-minute period the boiler will shut down
and may only be operated again after the electricity supply has been
disconnected. If the shutdown is occasional or an isolated event, this is
not a problem.





AIR PURGE
ACTIVE




10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston Alteas ONE Net at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston Alteas ONE Net in the language / languages: English as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info