48064
6
Zoom out
Zoom in
Previous page
1/16
Next page
4
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Ready, steady, go!
You can cancel
the wash cycle
in progress, if it
has only just
started.
Make sure the
wash cycle has
ended before
removing the
dishes!
If opening the
door soon after
the end of the
programme,or
during it, stand
away from the
Dishwasher, to
avoid possible
injury from hot
steam.
First of all.
After performing all the operations
described in the previous
paragraphs, turn the water tap on
completely and press ON-OFF
button "A": you will hear a short
beep and indicator light "B" lights
up. Now the appliance is on and
ready to be programmed.
Selecting the wash
cycle.
To select the wash cycle, turn knob
"D" clockwise until the reference
notch on the knob corresponds
with the number or symbol for the
cycle you wish to set (have a look
at the wash cycle table on page
6). A short beep will indicate the
start of the wash cycle and
indicator light "G" corresponding
to the cycle starting phase will light
up.
The dishwasher keeps
you informed.
Your dishwasher is fitted with
indicator lights (G) which light up
to indicate the cycle phase under
way.
Here are the symbols correspond-
ing to each cycle phase:
pre-wash, wash, rinses, drying.
At all times, your dishwasher tells
you which cycle phase is under
way.
Modifying a wash cycle
in progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Turn the knob
anti-clockwise until it reaches the
Reset position and, after a few
seconds, you will hear 4 beeps
and indicator light "G" will turn
off. This is to inform you that
all the settings have been can-
celled. You are now free to re-
set the correct wash cycle.
You've left out a dish?
Well, it happens to everyone.
Interrupt the wash cycle by
pressing the ON-OFF button,
insert the dish you had forgot-
ten and press the ON-OFF but-
ton again. The cycle will start
up from where you interrupted
it.
Finished?
The end of the wash cycle is
indicated by two short beeps
and the flashing of the drying
phase indicator light.
Turn the knob anti-clockwise to
Reset in order to reset all the
settings.
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam.
Empty the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity
comes back on or when you
shut the door. Everything is
under control!
Warning:
Turn the appliance off by
pressing button A, unplug
the appliance from the
electricity socket to cut off
the power supply; the power
supply cable should
consequently be easily
accessible.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston AFA370 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston AFA370 in the language / languages: English as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info