48060
4
Zoom out
Zoom in
Previous page
1/12
Next page
4
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Ready, steady, go!
First of all.
Turn on the water tap completely
and press ON-OFF button "A": a
short beep will sound and indicator
light "B" will come on. Now the
appliance is on and ready to be pro-
grammed.
Selecting the wash cycle.
To select a wash cycle, turn knob
"D" clockwise until the reference
notch on the knob corresponds with
the number or symbol for the cy-
cle you wish to set (have a look at
the wash cycle table on page 6).
After a few seconds, you will hear
a short beep: the wash cycle has
begun and it is not advisable to
make any changes at this point.
The dishwasher informs
you.
Your dishwasher is fitted with indi-
cator lights (G) that come on to
show you at which point the wash
cycle is at.
Here are the symbols correspond-
ing to each cycle phase:
Starting from the indicator light on
the left moving towards the one on
the right: pre-wash, wash, rinses,
drying.
At all times, your dishwasher tells
you where it is at.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Turn the knob
anti-clockwise and set it to Reset,
after a few seconds you will hear 3
beeps and indicator light "G" will
go out: this means all the settings
have been cancelled. You are now
free to re-set the correct wash cy-
cle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by pressing the
ON-OFF button, insert the dish you
had forgotten and press the ON-
OFF button again. The cycle will
start up from where you interrupted
it.
Finished?
The end of the wash cycle is sig-
nalled by 2 short beeps and a flash-
ing drying phase indicator light. Set
the knob to the Reset position to
clear all settings.
Turn the appliance off by pressing
button "A", thus cutting off the elec-
tricity supply.
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam.
Empty the lower rack first.
There's been a power fail-
ure? Have you opened the
dishwasher door?
The wash cycle stops and then re-
starts when the electricity comes
back on or when you shut the door.
Everything is under control!
If opening the
door soon after
the end of the
programme,or
during it, stand
away from the
Dishwasher, to
avoid possible
injury from hot
steam.
You can cancel
the wash cycle
in progress, if it
has only just
started.
Make sure the
wash cycle has
ended before
removing the
dishes!
You want to wash on one
rack only? Remember to
use half the amount of de-
tergent.
Your dishwasher also allows you to
wash half a load, to save water and
electricity. Before setting any wash
cycle, press button "H".
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston AF350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston AF350 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info