Manual Ariston AB1030C (page 12 of 15) (English)

47629

Zoom out

Zoom in

1/15

If despite all this your washer-dryer is still not running properly,

call your local Authorized Service Centre providing the

following information:

- fault

- model code (Mod. ....)

and serial number (S/N ....)

shown on the data plate at the back of your washer.

Never use the services of an unauthorised servicing technician

and insist on the use of original spare parts.

Installation

Transit packing

After removing the packing, check the appliance for damage.

If you have any doubts do not use the washer and call a qualified

technician. Keep the packaging components (plastic bags,

polyester foam, nails etc.) out of the reach of children since

they could be dangerous. The interior of the washer-dryer, has

an oscillating unit which is fixed on the back by 3 screws

during transport (figure 3). Before starting up the washer-dryer,

release the unit, by unscrewing the 3 screws. Seal the screw

holes with the plastic plugs supplied with the appliance.

Levelling

The washer-dryer must be perfectly levelled. To level the

appliance, only the front feet need to be adjusted

(see fig. 4); remember that the inclination of the working

surface must not be more than 2 degrees. If the washer-dryer

is installed on a carpeted floor, check that there is sufficient

ventilation space between the floor and the bottom of the

washer-dryer.

Water supply

Both hot and cold water supplies are preferable and they should

be between 34.5kN/m²(5lb/in²) and 1034.2kN/m² (150lb/in²)

pressure. The hose having the red end fitting should be en-

countered between the hot supply and the threaded connec-

tion adjacent to the letter H on the rear of the machine. The

hose having the white end fittings should be connected be-

tween the cold supply and the threaded connection adjacent

to the letter C on the rear of the machine (see fig. 5). Remem-

ber to insert a sealing washer at each connection to ensure

watertight joints. Do not overtighten the connections by

using tools -hand tight is sufficient to prevent leaks. It is gener-

ally more convenient to have these supplies away from the

sink taps. Where no suitable hot water supply is available or it

does not meet these requirements, both inlet hoses may be

connected to a cold supply by using two taps etc., or a «T»

junction on the plumbing (see fig. 6) however, use of cold

water only will increase programme times.

Note: the maximum temperature should not exceed 70°C

(158°F).

Drain hose

The drain hose (hooked pipe) is secured to the rear of the

machine by support clips and may be routed to right or left as

required (see fig. 7). The drain hose should be placed in a

stand pipe with a minimum internal diameter of 38 mm (1½

inches) or it can be positioned over a sink (see fig. 8) or it can

be connected as shown in fig. 9. The height of stand pipe or

sink should be between 60 and 100 cm (24 and 40 inches).

Care must be taken that the hose is not obstructed, twisted,

submerged or kinked. If the hose is connected with an airtight

joining, provision should be made to prevent syphoning.

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston AB1030C in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston AB1030C Manual

Product: