47601
2
Zoom out
Zoom in
Previous page
1/16
Next page
! Packaging materials are not childrens toys.
Levelling
1. Install the machine on a flat sturdy floor, without
resting it up against walls, cabinets etc.
2. Compensate for any unevenness by tightening or
loosening the adjustable front feet. When adjusting
the feet, use a spirit level to check the machine
stands level, from side to side and from front to
back.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the machine.
Water connection
Connecting the water inlet hose.
Remember that this is a cold-fill machine and the fill
hose fitted to the rear of the machine must be
connected to the cold water supply.
Before making the connections to the water outlet,
allow the water to run freely from the cold water
supply tap until it is perfectly clear.
Screw the cold water fill hose
onto the cold water supply tap
until tight.
Turn the tap on and check for leaks:
tighten if necessary.
! Make sure there are no kinks or bends in the hose.
! The water pressure at the tap must be within the values
indicated in the Technical details table (next page).
! If the water inlet hose is not long enough, contact a
specialist store or an authorised serviceman.
! Always use new hoses.
! Check the water hose at least once a year, replace
any that are cracked as worn hoses could split under
water pressure.
Installation
2
GB
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction manual
accompanies the washer dryer to inform the new
owner as to its operation and features.
! Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking
1. Unpack the machine.
2. Check whether the washer dryer has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
Remove the transit fixings
IMPORTANT: Follow these instructions to remove the
TWO transit fixings.
Situated one either side of the
rear panel, BOTH transit bolts
MUST be removed before use.
! Failure to do so may cause
damage to your machine.
It is important the transit bolt and
spacer (see pic) come out intact.
1. Unscrew the bolt using a
13mm spanner.
2. STOP
when 3 threads can be
seen.
3. Hold, slide sideways and pull
to remove.
4. For safety, insert one of the
plastic covers (supplied with
your machine) over the hole.
! Repeat steps 1 to 4 to remove
the second transit bolt.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston A1400WD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston A1400WD in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info