689099
16
Zoom out
Zoom in
Previous page
1/32
Next page
V 03/17
48
Before-use checks
1. Check that the air inlet and outlet are free of obstructions.
2. Check that the circuit breaker, plug and socket are in good working order.
3. Check that the filters are clean.
4. Check that the outdoor unit's support bracket is not damaged or corroded. If it is, contact
the service centre.
5. Check that the piping is not damaged.
After-use checks
1. Disconnect the power supply.
2. Clean the indoor unit's panel and filters.
3. Check that the outdoor unit's support bracket is not damaged or corroded. If it is, contact
the service centre.
TROUBLESHOOTING
Possible faults and solutions
WARNING
Do not attempt to repair the unit yourself. Improper repair can cause electric shocks or fire.
Disconnect the unit from the power supply before contacting your local Technical Service Centre.
Carry out the following checks before contacting your Technical Service Centre:
Fault Check Solution
Is there noticeable interference (e.g. static
electricity, stable voltage)?
Pull out the plug. After about 3 minutes
reinsert the plug and restart the unit.
Is the remote control within the signal
reception range?
Are there any obstacles between the
remote control and the receiver?
The maximum signal reception distance
is 8 m. The remote control will not work
beyond this distance.
Remove the obstacles.
Is the remote control pointed at the
receiver?
Point the remote control at the receiver
on the indoor unit.
Is the remote control's sensitivity low? Are
icons blurred or missing?
Check the batteries. If the batteries are
very low, replace them.
Do icons fail to appear on the display
when you operate the remote control?
Check if the remote control is damaged.
If it is, replace it.
The indoor unit
does not receive
the signal from
remote control or
the remote
control does not
seem to be
working
Is there a fluorescent light in the room? Position the remote control next to the
indoor unit.
Turn off the fluorescent light and try
again.
Is the indoor unit's air inlet or outlet
blocked?
Remove the obstruction.
In heat mode, has the indoor temperature
reached the set temperature?
Once the set temperature has been
reached, the indoor unit will stop blowing
out air.
No air comes out
of the indoor unit
Has heat mode only recently been
selected?
To prevent blasts of cold air from being
blown out, there will be a delay of
several minutes before operation begins
(this is normal).
Is there a power cut? Wait for the power to be restored.
Has the plug come loose? Reinsert the plug.
Has the circuit breaker tripped or has the
fuse blown?
Have the circuit breaker or fuse replaced
by a qualified technician.
Is the wiring faulty? Have it replaced by a qualified
technician.
Was the unit restarted immediately after
shutdown?
Wait 3 minutes and then restart the unit.
The air
conditioner is not
working
Is the setting on the remote control
correct?
Reset the function.
Fault Check Solution
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo X3MI 80 SH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo X3MI 80 SH in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info