Manual Argo X3i Eco Plus (page 17 of 60) (English)

805096

Zoom out

Zoom in

1/60

Autoclean function

With the unit off, press and hold the MODE and FAN buttons simultaneously for 5 seconds to activate or

deactivate the automatic cleaning function. When the automatic cleaning function is activated, the indoor unit

displays "CL".

The function will see condensation, ice formation, defrosting and drying phases take place in sequence aimed at

eliminating all residues of dust and pollutants and any trace of condensation from the evaporator. This will always

allow clean air to be introduced into the environment and to preserve the efficiency of the heat exchanger

During the automatic evaporator cleaning process, the unit will perform either rapid cooling or rapid heating.

There may be some noise and the air conditioner may blow out cold or hot air. During the cleaning process,

make sure the room is well ventilated.

The automatic cleaning function can only work in normal room temperature. If the room is dusty, clean it once a

month; otherwise, once every three months. After activating the automatic cleaning function, you can leave the

room. At the end of the automatic cleaning, the air conditioner will go back to stand-by.

Energy saving function

In cool mode, press the TEMP and CLOCK buttons simultaneously to start or stop the energy saving function.

When you start the energy saving function, "SE" will appear on the remote control display and the air conditioner

will automatically adjust the set temperature according to the factory settings to achieve the best energy-saving

effect. Press TEMP and CLOCK again simultaneously to exit the energy saving function.

N.B.:

• When the energy saving function is enabled, the fan will operate at the default automatic speed and cannot be

adjusted.

• When the energy saving function is enabled, the set temperature cannot be adjusted. The remote control will not

send a signal to the unit when the TURBO button is pressed.

• The SLEEP and energy saving functions cannot operate simultaneously. If the energy saving function was set in

cool mode, press the SLEEP button to cancel it. If the SLEEP function was set in cool mode, start the energy saving

function to cancel it.

8°C heating function

In cool mode, press the TEMP and CLOCK buttons simultaneously to start or stop the 8°C heating function. When

this function is enabled, and 8°C will appear on the remote control display and the air conditioner will continue

to operate at 8°C. Press TEMP and CLOCK again simultaneously to exit the 8°C heating function.

N.B.:

• When the 8°C heating function is enabled, the fan will operate at the default automatic speed and cannot be

adjusted. The remote control will not send a signal to the unit when the TURBO button is pressed.

The SLEEP and 8°C heating functions cannot operate simultaneously. If the 8°C heating function was set in cool

mode, pressing the SLEEP button will cancel it. If the SLEEP function was set in cool mode, starting the 8°C heating

function will cancel it.

• When the temperature display is in °F, the remote control will show that the unit is operating at 46°F.

Remote control button lock function

Press "▲" and "▼" simultaneously to enable or disable the remote control button lock function. When this function

is enabled, will appear on the remote control display. If you attempt to operate the remote control, the icon

will flash three times and no signal will be sent to the unit.

Switching temperature display

In OFF mode, press the "▼" and "MODE" buttons simultaneously to switch from a temperature display in °C to

°F.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Argo X3i Eco Plus in the language / languages: English as an attachment in your email.

The manual is 3.74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo X3i Eco Plus

Argo X3i Eco Plus User Manual - German - 63 pages

Argo X3i Eco Plus User Manual - French - 63 pages

Argo X3i Eco Plus User Manual - Italian - 60 pages

Argo X3i Eco Plus User Manual - Spanish - 62 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Argo X3i Eco Plus Manual

Product: