689096
13
Zoom out
Zoom in
Previous page
1/32
Next page
V 03/17
45
N.B.:
When the 8°C heating function is enabled, the fan will operate at the default automatic speed
and cannot be adjusted. The remote control will not send a signal to the unit when the
TURBO button is pressed.
The SLEEP and 8°C heating functions cannot operate simultaneously. If the 8°C heating
function was set in cool mode, pressing the SLEEP button will cancel it. If the SLEEP
function was set in cool mode, starting the 8°C heating function will cancel it.
When the temperature display is in °F, the remote control will show that the unit is operating
at 46°F.
Remote control button lock function
Press "▲" and "▼" simultaneously to enable or disable the remote control button lock function.
When this function is enabled,
will appear on the remote control display. If you attempt to
operate the remote control, the
icon will flash three times and no signal will be sent to the
unit.
Switching temperature display
In OFF mode, press the "▼" and "MODE" buttons simultaneously to switch from a temperature
display in °C to °F.
Operating guide
1. When you connect the power, press the "ON/OFF" button on the remote control to turn the
air conditioner on.
2. Press the MODE button to select the desired operating mode: AUTO, COOL, DRY, FAN or
HEAT.
3. Press "▲" or "▼" to adjust the desired temperature. (The temperature cannot be adjusted
in automatic mode.)
4. Press the "FAN" button to set the desired fan speed: automatic, low, medium or high.
5. Press the "SWING" button to adjust the fan's angle of airflow.
Replacing the remote control batteries
1. Remove the battery compartment cover, marked with
(see image to right), by sliding it in the direction of
the arrow.
2. Use only two AAA LR03 1.5V batteries. Make sure
the + and – ends are facing the correct direction.
3. Slide the battery compartment cover back into place.
trasmittente
segnale
coperchio vano batterie
rimozione
reinserimento
batterie
trasmittentesegnale signaltransmitter
batterie batteries
reinserimento close
rimozione open
coperchiovanobatterie batterycompartmentcover
N.B.:
When the unit is operating, point the remote control's signal transmitter at the indoor unit's
receiver.
The distance between the transmitter and the receiver must not exceed 8 metres and
should remain free of obstacles.
If the room contains a fluorescent light or cordless telephone, signal interference is likely to
occur.
When the remote control is not used for a month or more, remove the batteries.
Use batteries of the same type when replacing the batteries, as necessary.
If the icons on the remote control display are blurred or not visible, replace the batteries.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo X3I 52HL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo X3I 52HL in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info