665612
7
Zoom out
Zoom in
Previous page
1/9
Next page
V 06/17
17
2. By supporting the bracket onto the wall, mark on the wall with a pencil the points where it is necessary to make
the holes in order to insert the Fishers. Observe the minimum distances from the walls.
3. Place the heater into suitable position ensuing that the holes align with bracket and drill holes in the wall and insert the
Fishers. Secure the bracket to the wall and insert the screws supplied.
4. Tighten the screws at the top of the convector firmly.
HOW TO USE THE CONVECTOR
Connect the power cord to a suitable electric socket (220-240V~/50Hz).
ON/OFF switch (on the right side)
Bring the on/off switch to the “I” position.
When the appliance emits a beep this means that the convector is ready for use.
Bring the switch to the “O” position to switch off the convector.
CONTROL TOUCH PANEL
MODE button
Touch this button to regulate the heating mode:
- Eco (750W)
- Comfort (1500W)
TEMPERATURE button
Internal temperature is displayed every time
the appliance is started up.
When the appliance is in stand-by or
heating, touching this button will allow you to
set the temperature: the display will show
ambient temperature and, by touching this
button, the desired temperature can be set
between 16 and 40°C. Once the desired
temperature has been set, wait 5” for the
setting to be confirmed. After 5” the display
will show the ambient temperature once
again. The set default temperature is 25°C.
When room temperature is 2 degrees over
the set temperature, the appliance will stop
operating. The machine will begin operating
again only when temperature decreases 2
degrees with respect to the set temperature.
TIMER button
When the appliance is operating, the
operating time can be set by touching
this button: the timer display shows a
flashing 0 and touching TIMER you
can set the desired time, between 1
and 24 hours, with each touch
corresponding to an hour.
The display shows the set time: wait
5” for the setting to be confirmed. The
unit will switch off automatically at the
end of the programmed time (stand
by).
In order to switch it on again press the
button ON/OFF.
If a TIMER is set the LED remains
on.
ON/OFF buttons
Touching the ON/OFF button will cause the
LED to
light and the appliance will begin to operate.
The display will show ambient temperature.
The heater is working at low power heating
conditions.
To switch off the convector completely, place the on/off
switch in the “OFF” position.
Led display
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Minimal at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Minimal in the language / languages: English as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Minimal

Argo Minimal User Manual - German - 10 pages

Argo Minimal User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info