724571
14
Zoom out
Zoom in
Previous page
1/17
Next page
V 11/19
31
(3) SLEEP BUTTON (on both the remote control and portable unit)
Press this button to reduce to minimum the ventilation, for the most silence.
Note: The sleep mode cannot be started in ventilation mode.
(4) FAN SPEED ADJUSTMENT BUTTON
Press this button when the appliance is switched on for adjusting the ventilation speed in cooling mode (AUTO), to low
(Low), medium (Med) or high (High).
The fan speed cannot be adjusted in DRY mode and is fixed to low speed.
(5) TIMER BUTTON (on both the remote control and portable unit)
Press and hold this button for 1 second to set the timer.
1Timer-on (automatic switch-on)
When the appliance is off, this button is used to set a delay after which the unit will switch on.
Remote control: press “TIMER” to set a time to turn on the air conditioner. Press +/- to set the time, and press
“TIMER” again to confirm it. The “G” icon will remain on to indicate that the TIMER has been set.
Portable unit: Press TIMER. Press Timer again to select a number of hours from 1 to 24. Press the TIMER button
to confirm.
2Timer-off (automatic switch-off)
When the appliance is running in the COOL mode, set a delay after which the unit will switch off.
Remote control: press “TIMER” to set a time to turn on the air conditioner. Press +/- to set the time, and press
“TIMER” again to confirm it.. The “G” icon will remain lit to indicate that the switch-off TIMER is running.
Portable unit: Press TIMER. Press Timer again to select a number of hours from 1 to 24. Press the TIMER button
to confirm.
Resetting the timer: If a TIMER has been set, press TIMER to display the delay. Press TIMER again to cancel the
setting.
(6) “SWING” BUTTON
Press “SWING” top turn on or off the swing function.
(7) TEMPERATURE + - AND TIMER ADJUSTMENT BUTTONS
The temperature can be adjusted to between 16 °C and 30 °C.
Increase temperature+):
1) Allows for adjusting the desired temperature in cooling (COOL) mode.
2Whenever the
+) button is pressed, the set temperature increases by 1 °C.
Decrease temperature (
- ):
1) Allows for adjusting the desired temperature in cooling (COOL) mode.
2Whenever the (
- ) button is pressed, the set temperature decreases by 1 °C.
The same button allows for setting the TIMER.
(9) TANK OVERFLOW INDICATOR
If the tank is full this led will turn on.
(8) TEMPERATURE AND ERROR DISPLAY
In the event of a malfunction, the LED display shows an error code, which facilitates the solution of the problem. With
the exception of the FL message, full tank, when an error occurs do not attempt to repair the air conditioner, always
take it to an Argoclima Service Center.
Problem Cause Solution
FL Tank full of water. Empty the tank.
If the problem persists, contact a service centre.
E1 Room temperature sensor failure. Contact a service centre.
E2 Failure of temperature sensor on the
evaporator.
Contact a service centre.
Il display temperatura ed errori si accende solo nelle modalità COOL. Nelle modalità DRY e FAN non si accende
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo IRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo IRO in the language / languages: English as an attachment in your email.

The manual is 2,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo IRO

Argo IRO User Manual - German - 17 pages

Argo IRO User Manual - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info