665659
8
Zoom out
Zoom in
Previous page
1/9
Next page
10
V 12/16
OPERATING INSTRUCTIONS
Read the instructions carefully before operating the appliance or carrying out maintenance operations.
Observe all the safety instructions; failure to do so may lead to accidents and/or damage. Store these
instructions in a safe place for future reference.
SMART FAN
EN
11
V 12/16
GENERAL SAFETY INFORMATION
Only use this appliance as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock or injury to persons.
Make sure that the type of mains power complies with the electrical
requirements of the appliance (230 V~/50 Hz).
This appliance can be used by children older than 8 years and by
people with reduced physical, sensory or mental abilities, or who
lack sufficient experience or the necessary knowledge, provided that
they are supervised or have been instructed on how to use the
appliance safely and understand the hazards related to its use.
Children must not be allowed to play with the appliance.
Cleaning and maintenance operations normally carried out by the
user must not be performed by unsupervised children.
This product is not a toy. Children should be adequately supervised
to ensure that they do not play with it.
Disconnect the mains power when the appliance is not in use or
during cleaning operations.
Switch off the appliance immediately in case of
anomalies; do not attempt to repair it, but take it to the
local technical assistance centre.
Do not remove or replace parts personally, as this could
jeopardise the product's safety.
Do not touch the power cord with damp hands, as
you may risk getting an electric shock.
12
V 12/16
Do not insert objects into the appliance's grilles.
This may cause leakages, short-circuits and damages to
the product.
Do not spray flammable substances or pesticides
near the product as they could damage it.
Do not leave the airflow directed towards children for
long periods of time: it is unhealthy.
Do not pull or drag the power cord after unplugging
it. This may damage the cord and cause
dispersions and other hazards.
Make sure that the power cord is not attached to other
objects and that it is plugged in properly, or power
losses may occur.
Managing exceptions
If the product emits an unpleasant odour or
anomalous noise during operation, immediately
stop working and disconnect the power cord.
Do not use the appliance if the power cord or plug are
damaged. Do not attempt to change the power cord
yourself. If the power cord is damaged, it must be
replaced by the manufacturer, dealer or a similarly
qualified person so as to prevent any safety risks.
Do not fold or place heavy objects on the power
cord.
13
V 12/16
Do not pour water on the product: this may cause a
short-circuit and damages to the product.
Do not use the appliance near a bathtub, shower or
swimming pool.
Never use the appliance directly under a power
outlet.
Keep the appliance far from walls, curtains and
other combustible materials when in use, in order
to prevent fires.
Always switch the appliance off when it is not used for
prolonged periods, and always pull out the power cord
when it is not used.
Avoid using the appliance when children, animals or
people lacking motor abilities or self-control are present
and unsupervised.
Check that the power outlet fulfils the specified
requirements. It must be able to bear a load of at
least 10 A / 220 V.
Make sure that the power supply voltage matches
the rated voltage indicated on the rating plate.
Check the relevant voltage specifications whenever
the appliance is transferred to a new place.
Do not cover the appliance to avoid overheating.
Do not place any object on the appliance.
14
V 12/16
DESCRIPTION OF PARTS
1. Air entry on right
2. LED indicator
3. Right-hand side panel
4. Touch control panel
5. Rear structure
6. Power cord
7. Nut support
8. Air entry on left
9. Decorative panel
10. Left-hand side panel
11. Front structure
12. Presence sensor
13. Remote control receiver
14. Swinging base
15. Remote control
16. Remote control support
17. Shaft
18. Base
19. Base weight balancing system
HOW TO USE THE APPLIANCE
INSTALLATION INSTRUCTIONS
The appliance must be installed. Observe the following instructions:
1. Extract the parts from the package to assemble them.
2. Attach the shaft to the hole on the base and secure it tightly with the screw (Picture 1).
3. Attach the fan body to the shaft (Picture 2).
4. Secure the fan body and shaft with the screw (Picture 3).
5. Place the fan on a flat surface, switch it on and follow the instructions of the user manual. (Picture 4).
Picture 1 Picture 2 Picture 3 Picture 4
15
V 12/16
Place the unit on a flat and stable surface and connect the power cord to a suitable power outlet (230 V~): the appliance
can be switch on using the ON/OFF switch.
This product can be used as a fan – in 4 modes (Normal, Natural, Sleep and ECO-Normal) and with 3 fan speed
options (medium-low, high and low).
The buttons are all touch controls, so the functions can be activated by touching the corresponding buttons on the control
panel.
When the appliance is switched on, all the LED lights turn on for 2 seconds and emit a double beep to signal that the unit
is functioning correctly. All the LED lights then turn off and the unit enters the stand-by mode.
In stand-by mode only the ON/OFF button works, so pressing it allows for starting the unit. The unit is initially set to low
speed in NORMAL mode without the timer nor the rotation function, as evidenced by the lit LEDs.
Memory function
All the operating modes, with the exception of the Timing and Sleeping modes, will be memorised; the fan will operate
with the same functions when switched on the next time.
Energy saving function
The LED indicators will automatically lower their original brightness by 30% if no operations occur on the control panel
after 1 minute. Pressing any button again restores the original brightness.
DISPLAY AND CONTROL PANEL
ON/OFF BUTTON
Press the ON/OFF button to switch the appliance on. When the appliance is switched on it enters the stand-by mode and
all the LED lights turn on for 2 seconds.
MODE BUTTON
The fan is initially set to Normal mode; press the MODE button to select other operating modes: ‘Normal’ –
‘Natural’ – ‘Sleeping’ – ‘ECO-Normal’. Depending on the selected mode, the corresponding LED indicator will
light up; the LED indicator does not light up in Normal mode, but does so in the other corresponding modes.
Press the MODE button to select the fan speed:
- Normal mode: the unit operates with three constant ventilation speeds: high, medium and low.
- Natural mode: the unit operates by alternating the three ventilation speeds according to the following schemes in
relation to the set ventilation speed.
5. HORIZONTAL
SWIVELLING/
PRESENCE
SENSOR
6. VERTICAL
SWIVELLING
4. SPEED 1. ON/OFF 3. TIMER 2. MODE
16
V 12/16
- Sleeping mode: the unit operates at high natural ventilation speed and decreases by one level every 30 minutes;
1. High speed: the unit operates for 30 minutes according to the high-speed Natural mode scheme (see previous page);
30 minutes according to the medium-speed Natural mode then continues operating according to the low-speed
Natural mode scheme.
2. Medium speed: the unit operates for 30 minutes according to the medium-speed Natural mode scheme (see previous
page) then continues operating according to the low-speed Natural mode scheme.
3. Low speed: the unit operates according to the medium-speed Natural mode scheme (see previous page) then
continues operating according to the low-speed Natural mode scheme.
- ECO-Normal mode:
The Eco-Normal mode has the following specific functions: when the ambient temperature is below 25°C, the unit
operates at low ventilation speed; when the ambient temperature is between 25°C and 29°C, the unit operates at medium
ventilation speed; when the ambient temperature exceeds 29°C, the unit operates at high ventilation speed.
In this mode the ventilation speed cannot be adjusted and the Speed LED does not light up.
TIMER BUTTON
While the unit operates, the time can be set to one of the following settings: 1h – 2h – 4h – 8h. Once a time has been set,
the corresponding LED indicator will light up on the display. Once the set time has elapsed, the appliance will return to the
stand-by mode.
SPEED BUTTON
When the appliance is switched on, press the SPEED button to choose between the medium-low, high or low speed
setting. The corresponding LED indicator will light up.
VERTICAL SWIVELLING BUTTON AND PRESENCE SENSOR
When the appliance is on, press this button to set the horizontal swivelling range: 0° (no horizontal swivelling) 60°, 90°,
180°, 360°; the indicators will light up depending on the selected swivelling range.
To activate the presence sensor press and hold for 2.5 seconds: the appliance will emit a double beep and the LED
indicators of the swivelling range will light up in succession.
The presence sensor activates once the unit has rotated through 360° and after the swivelling button has been pressed
again; in this case, the sensor attempts to detect any people present then selects the correct swivelling range
automatically.
If no person is detected, the unit makes a new attempt by automatically repeating the 360° rotation movement. If new
people appear after the appliance has already selected the swivelling range, the users must press the button again to
activate the presence sensor.
If several people are present, the appliance will modify its tilt angle to approach each person and guarantee the
appropriate level of comfort for each specific position.
The sensor detects the presence of people within 2 metres from the fan.
High speed
Medium speed
Low speed
Stop
Medium speed
Low speed
Stop
Natural mode at high speed
Natural mode at medium speed
Natural mode at low speed
High speed
Medium speed
Low speed
Stop
17
V 12/16
VERTICAL SWIVELLING BUTTON
When the unit is on, the vertical swivelling movement is not active. The users can press the Vertical Swivelling button to
set the vertical swivelling movement while the appliance operates. The indicator will light up; press this button again to
switch off the vertical swivelling function.
HOW TO INSERT / REMOVE THE REMOTE CONTROL BATTERIES (refer to the diagram below)
Open the battery cover at the back of the remote control (press the back and pull the flap).
Insert the battery in the slot, while making sure to respect the polarity.
Slot the cover back into place on the remote control.
Use lithium/manganese button cells, model no. CR2032 -3 V, conforming to Battery Directive no. 2006/66/EC (supplied with
the remote control).
Point the remote control towards the receiver. The remote control will not function if the receiver is blocked. Hold the remote
control properly and do not throw it on the ground.
REMOTE CONTROL
INFORMATION FOR THE CORRECT DISPOSAL OF BATTERIES IN ACCORDANCE WITH EUROPEAN DIRECTIVE
2006/66/EC
Replace batteries when they are depleted. At the end of their life, batteries must be disposed of separately from unsorted waste.
They must be taken to designated recycling centres or returned to a retailer providing this service. Separate disposal of batteries
prevents potential negative effects on the environment and human health due to inadequate disposal, and also allows for
recovering and recycling their constituent materials, resulting in significant savings in terms of energy and resources. The
separate disposal obligation is underlined by the crossed-out dustbin symbol appearing on the battery. Illegal disposal of the
product by the user implies administrative sanctions applied as per current regulations.
2
6
4
1
5
3
18
V 12/16
MAINTENANCE AND STORAGE
CAUTION: ALWAYS UNPLUG THE APPLIANCE BEFORE CLEANING OR MAINTENANCE
OPERATIONS.
IMPORTANT: DO NOT SUBMERGE THE PRODUCT IN WATER.
Cleaning the outside surface of the appliance
If the front grille of the fan is excessively dusty or dirty, the outward flow of air may be hampered; for this reason, the fan
should be cleaned frequently, at least once a month.
Use a soft cloth to remove any dust from the product. Should this not suffice, use a soft cloth dampened with water and a
neutral detergent. Let the appliance dry completely before using it.
Do not use corrosive detergents or solvents such as petrol. Do not wash the appliance with water. When cleaning the
appliance, do not use oils, chemical substances or other items that may damage the surface.
Use a vacuum cleaner to remove dust from the air inlet/outlet grilles.
STORAGE
If the appliance is not used for prolonged periods, disconnect the power cord and store the appliance with this manual in its
original packaging, in a cool and dry place.
INFORMATION FOR THE CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EUROPEAN
DIRECTIVE 2012/19/EU
This appliance must not be disposed of with household waste when it reaches the end of its useful life. We highlight the
crucial role played by the consumer in contributing to the reuse, recycling and other forms of recovery of such waste.
The dismantled appliance, with its components collected separately, must be delivered to the local waste disposal
facility or returned to the dealer free of charge when purchasing a new equivalent appliance.
Sorted disposal of electric and electronic equipment prevents potentially negative consequences on the environment
and human health due to improper scrapping, and also allows the constituent materials to be recovered and recycled,
with significant savings in terms of energy and resources.
The sorted disposal requirement is indicated by the crossed-out wheeled bin symbol affixed to the product.
www.argoclima.com
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Genius at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Genius in the language / languages: English as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Genius

Argo Genius User Manual - German - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info