665483
27
Zoom out
Zoom in
Previous page
1/30
Next page
EG
27
To enter the conguration menu, with Emix already on, press and hold the BUTTON 9 for about 7 seconds.
When only the RED LED lights up, keep BUTTON 9 pressed until the BLUE LED lights up. At this point release BUTTON 9.
After 5 seconds without any operation, Emix exits the conguration procedure and returns to the previous menu.
Booster mode setting
The use of electrical heating elements installed in a storage tank or in a electrical water heater allows you to heat the cold
water faster, to reach the desired water temperature even in conditions of very low external temperatures or to heat the
water even if the heat pump is switched off for maintenance.
When you activate the Booster mode, the software will automatically handle the electrical heaters.
If after 120‘ from start up of the system (the time counter starts when the Booster mode is set), the water setpoint is not
reached, the rst electrical element is automatically activated. The other elements, one by one, will be activated every
120‘ following the course of the water temperature, until reaching the setpoint.
To activate / deactivate the Booster mode, from the conguration menu, quickly press BUTTON 9 until the only BLUE
LED is ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default, the Booster mode is off.
Super Booster mode setting
When the Super Booster mode is activated, all the connected electrical heaters will be activated at the same time, to-
gether with the heat pump.
When the setpoint is reached, all electrical heaters are switched off and the Super Booster mode is automatically turned
off.
To activate / deactivate the Super Booster mode, from the conguration menu, quickly press BUTTON 9 until the only
RED LED is ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default, the Super Booster mode is off.
EMIX CONFIGURATION
Setpoint limit setting with Heat Pump
It is possible to set the maximum achievable setpoint when the Heat Pump is working only for Emix. This limit can be set
to 50°C or 58°C.
To change the setting, from the conguration menu, quickly press BUTTON 9 until the BLUE and YELLOW LEDs are
ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default the limit is set to 50°C. We recommend to keep this setting to preserve the Emix performance.
Antilegionella cycle setting
To activate / deactivate the Antilegionella cycle, from the conguration menu, quickly press BUTTON 9 until the only YEL-
LOW LED is ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default, the Antilegionella cycle is on. It is highly recommended to keep it enabled.
For details on the operation of the Antilegionella cycle, see section “ANTILEGIONELLA CYCLE”.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Emix Tank at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Emix Tank in the language / languages: English, German, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Emix Tank

Argo Emix Tank User Manual - English - 29 pages

Argo Emix Tank User Manual - German - 29 pages

Argo Emix Tank User Manual - French - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info