665483
18
Zoom out
Zoom in
Previous page
1/30
Next page
EG
18
In case of Emix is connected to a normal indoor unit port (for example with G30 or G42) the unit must be disconnected
exactly as any other air indoor unit. On the outdoor unit electrically disconnect the reversing valve to force the system in
cooling.
In case of Emix is connected to the Emix port and by any reason it has to be disconnected and replaced, the installer has
to do this procedure using a refrigerant recovery unit:
- close the valves of Emix port that connect Emix to outdoor unit;
- connect the refrigerant recovery unit to one of the two valves;
- recover the refrigerant inside the copper pipes and Emix unit;
- disconnect Emix;
- reconnect another Emix unit;
- make the vacuum;
- restore the refrigerant from recovery unit to the pipe and Emix unit;
- disconnect the recovery unit;
- re-open the valves of Emix port that connect Emix to outdoor unit.
In case of Emix is connected to the Emix port and by any reason it has to be removed denitively, the installer has to do
this procedure using a refrigerant recovery unit:
- close the valves of Emix port that connect Emix to outdoor unit;
- connect the refrigerant recovery unit to one of the two valves;
- recover the refrigerant inside the copper pipes and Emix unit;
- disconnect Emix;
- reconnect the bypass disconnected during the rst installation;
- disconnect the recovery unit;
- make the vacuum on the bypass;
- re-open the valves of Emix port that connect Emix to outdoor unit;
- switch on the outdoor unit in cooling mode;
- recover the refrigerant inside the system connecting the recovery unit to one of the liquid valve of indoor units or to the
pressure valve of the inlet tube;
- disconnect the recovery unit.
HOW TO DISCONNECT AND REMOVE EMIX UNIT
Emix could be connected to any type of thermal solar system, both natural and forced circulation.
In case of forced circulation solar system, by the water point of view, Emix must be connected to the solar tank exactly
like any other tank in parallel to the cold and hot tap water (mixing valve); by the electric point of view Emix could be
submitted to the solar control box if it has a dry contact to enable/disable Emix energy support to the water. In case the
solar control box does not have any backup contact, Emix will run in parallel mode with the solar system and obviously
will stop immediately the operation if the water is already hot by the sun. See section “Home Automation connections”
for connection to an external input signal.
In case of solar panel with natural circulation, the tank of the panel is equivalent to the normal tank connected to the
Emix. Connect in parallel the cold and hot tap water is enough to make working together the solar panel and Emix, but
take care about two important matters:
• elevation between Emix and solar tank cannot be more than the 7,5 meters, the max. elevation supported by the
Emix water pump to work properly;
• higher temperature of water due by the sun in some geographical areas; if the water temperature exceeds 95°C is
better to install a security system in temperature, in order to avoid over temperature of the Emix internal components.
(check hydraulic layouts).
HOW TO CONNECT EMIX TO A SOLAR THERMAL SYSTEM
INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN
DIRECTIVE 2012/19/EU
At the end of its working life this equipment must not be disposed of as an household waste.
It must be taken to special local community waste collection centres or to a dealer providing this service.
Disposing of an electrical and electronic equipment separately avoids possible negative effects on the environment
and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled
to obtain significant savings in energy and resources.
In order to underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Emix Tank at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Emix Tank in the language / languages: English, German, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Emix Tank

Argo Emix Tank User Manual - English - 29 pages

Argo Emix Tank User Manual - German - 29 pages

Argo Emix Tank User Manual - French - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info