724568
9
Zoom out
Zoom in
Previous page
1/41
Next page
V 09/19
49
When you select dry mode, the air conditioner will run at low speed in dry mode. The indicator
will illuminate on the display. The fan speed cannot be adjusted in this mode. Pressing the
"SWING" button will allow you to adjust the angle of airflow.
When you select fan mode, the air conditioner will operate only the fan, blowing air without cooling
or heating. All the indicators will switch off. Press the "FAN" button to adjust the fan speed.
Pressing the "SWING" button will allow you to adjust the angle of airflow.
When you select heat mode, the air conditioner will run in heat mode. The indicator will
illuminate on the display. Press "" or "" to adjust the set temperature. Press the "FAN" button
to adjust the fan speed. Pressing the "SWING" button will allow you to adjust the angle of airflow.
N.B.:
To prevent blasts of cold air from being blown into the room, there will be a delay of 1 – 5 minutes
after selecting heat mode before operation begins. (The actual delay will depend on the indoor
ambient temperature).
The temperature can be set between 16 – 30°C and four fan speeds are available: automatic,
low, medium and high.
3. FAN button
Pressing this button will allow you to cycle through and set the fan speed: automatic (AUTO),
low ( ), medium ( ) or high ( ). When turning on the unit, the AUTO ventilation
speed is activated automatically. With automatic speed, the unit automatically selects the fan
speed best suited according to the factory settings. In DRY mode (dehumidification), only the
low ventilation speed can be set.
Note:
The fan speed in dehumidification mode is low.
Pressing the ventilation speed button in Cooling or Dehumidification mode for 2 seconds
activates the X-FAN function and the icon appears on the remote control: the unit will continue
to ventilate for a few minutes, even after the unit is turned off, to dry the battery of the indoor unit,
thus avoiding the formation of mold. This function is not available in Auto, Ventilation or Heating
mode.
If the X-FAN function has been selected: after turning the unit off with the ON / OFF button, the
fan of the indoor unit will continue to run for a few minutes at low speed. During this time press
the FAN button for 2 seconds to stop the fan.
If the X-FAN function is not selected, when the air conditioner is turned off by pressing the ON /
OFF key, the fan switches off together with the unit.
4. / button
Press "" or "" once to increase or decrease the set temperature by 1°C. (The temperature
cannot be adjusted in automatic mode).
When setting the TIMER ON, TIMER OFF, press "" or "" to adjust the time.
5. SWING button – vertical oscillation
Press this button to set the swing angle (up/down). You can cycle through and set the fan's angle
of airflow as shown below:
nessuna visualizzazione (il deflettore orizzontale si arresta nella
posizione corrente)
no display (the horizontal flap stops in the current position)
nessuna
visualizzazione
(il deflettore orizzontale si arresta
nella posizione corrente)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo ECOLIGHT SINGLE SPLIT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo ECOLIGHT SINGLE SPLIT in the language / languages: English as an attachment in your email.

The manual is 5,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo ECOLIGHT SINGLE SPLIT

Argo ECOLIGHT SINGLE SPLIT User Manual - German - 47 pages

Argo ECOLIGHT SINGLE SPLIT User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info