724566
13
Zoom out
Zoom in
Previous page
1/16
Next page
13
During the heating mode, the air conditioner will now operate with the new calibration of the air probe.
Nota: this setting has no effect when I Feel is selected. In this case the air conditioner will operate with the remote
control air probe.
ATM mode setting
It is possible to set the air conditioner to operate automatically without a remote control so that it maintains the room
temperature between 18°C and 24°C. A typical application is that of installation within ATMs (cash machine) of banks. In
this mode it is not necessary to set the desired temperature or operating mode, but it will all be managed automatically
by the air conditioner.
To activate this mode, follow the procedure below:
1. Press and hold the “FILTER” button (symbol) for more than 7 seconds. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 11 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver. An acoustic confirmation of 4 consecutive “beeps” will confirm the successful setting.
Nota: 60 seconds after activating ATM mode the remote control is disabled.
To disable ATM mode, follow the procedure below:
1. Disconnect the power of the air conditioner
2. Wait for 1 minute
3. Re-connect power to the air conditioner
4. Within 60 seconds (before the remote control is disabled again), repeat the procedure above. An acoustic confirmation
of 2 consecutive “beeps” will confirm that the original setting has been reset.
Display setting : Celsius degrees / Fahrenheit degrees
The remote control is set by default to display the temperature expressed in Celsius degrees.
To change the temperature display from Celsius degrees to Fahrenheit degrees (and vice versa), follow the procedure
below:
1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 77 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it. The temperature will now be displayed on
the remote control screen with the new setting.
Note: if you remove the batteries from the remote control, the default display is reset.
Factory settings’ reset
To reset the factory settings, follow the procedure below:
1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 0 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver. An acoustic confirmation of 2 consecutive “beeps” will confirm the correct reset of the factory
settings.
Note: to reset the temperature display in Celsius degrees, remove and replace the batteries of the remote control unit.
EN
3742551750-I-AR-DD.indd 13 11/09/2019 13:41:38
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo DD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo DD in the language / languages: English as an attachment in your email.

The manual is 1.75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo DD

Argo DD User Manual - English - 15 pages

Argo DD Installation Guide - German - 16 pages

Argo DD User Manual - German - 16 pages

Argo DD Installation Guide - French - 16 pages

Argo DD User Manual - French - 16 pages

Argo DD User Manual - Italian - 16 pages

Argo DD Installation Guide - Italian - 16 pages

Argo DD User Manual - Portuguese - 16 pages

Argo DD Installation Guide - Portuguese - 16 pages

Argo DD User Manual - Spanish - 16 pages

Argo DD Installation Guide - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info