Manual Argo AWIBS9DC (page 46 of 72) (English, German, French, Italian, Portuguese, Spanish)

689101

Zoom out

Zoom in

1/72

(3) AUTOMATIC ADDRESSING PROCEDURE

System requirements:

Outdoor unit must have a recent firmware version that supports the automatic addressing procedure.

Indoor units must have a recent firmware version that supports the automatic addressing procedure

Dip-switch for communication address setting on the indoor unit (SW1) must be left to the factory default state, i.e. to the

OFF position.

Activation of automatic addressing procedure

Power on the whole system.

Verify that there is no error on the indoor units, but the error “Address not set” (see Auto-diagnosis table).

Switch on the remote controller of any of the indoor units of the system and set it as follows:

SETTING

AUTO

24°C

AUTO

OFF

Any

filter

night mode / high mode

iFeel

Fan

BUTTON

working mode (COOL - HEAT)

set point

flap

Press together FAN + IFEEL buttons for more than 7 seconds and release them pointing the remote controller to the indoor

unit receiver. Be sure to send the signal to only one indoor unit and that there is no other indoor unit that could receive the

same signal.

If the signal is received, the indoor unit will emit 5 consecutive beeps.

After some seconds, every indoor unit will show the following LED combination to confirm that the automatic addressing

procedure has been activated.

OPERATION STANDBY TIMER

ON OFF BLINKING

End of automatic addressing procedure

When all the circuits have been tested and the address of every indoor unit has been set, the outdoor unit will stop and every

indoor unit will switch off (standby mode).

In any case (procedure successful or failed) the infrared receiver of every indoor unit will be re-activated.

If there is no error on the indoor units, the system is ready to be used.

If there is the error “Address not set” (see Auto-diagnosis table) on any indoor unit, re-run the automatic addressing procedure

or manually set the address on that indoor unit with the dip-switch or with the remote controller.

From this moment until the end of the procedure the indoor units will not receive anymore the signals from the remote

controllers (infrared receiver is disabled).

Execution of automatic addressing procedure

Once the procedure has been activated, the system will run automatically to set the address of every indoor unit. In this period,

compressor and fan motor will be activated.

Once activated, the procedure takes about 4-5 minutes per outdoor unit circuit to be completed. This time doesn’t depend

on the number of indoor units actually connected to the outdoor unit, but on the number of refrigerant circuits of the outdoor

unit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Argo AWIBS9DC in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo AWIBS9DC

Argo AWIBS9DC User Manual - English, German, French, Italian, Portuguese, Spanish - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Argo AWIBS9DC Manual

Product: