665475
77
Zoom out
Zoom in
Previous page
1/84
Next page
47
F
D
I
REFRIGERANT CIRCUIT CHECK •
CONTROLLO CIRCUITO REFRIGERANTE
• CONTROLE DU CIRCUIT DE REFRIGERATION
NACHPRÜFUNG DER KÜHLROHRE
• COMPROBACIÓN DEL CIRCUITO DE REFRIGERACIÓN •
VERIFICAÇÃO DE
TUBAGENS DE REFRIGERANTE
¢π∞¢π∫∞™π∞ ƒÀ£ªπ™∏™ æÀ∫Δπ∫√À ∫À∫§øª∞Δ√™
1.Power ON the system.
2.Set the remote controller of unit A as following (units B, C and D must be OFF):
-Mode: COOLING
-Filter: ON
-Set-point: 32°C
3.Press FAN + IFEEL button for at least 5 seconds, pointing the remote control unit directly at the air conditioner
receiver.
System starts and runs for 3 minutes.
During this operation TIMER led is flashing, while OPERATION led is ON.
After 3 minutes’ operation:
- In case the setting is right, the unit switches to COOL mode and stops (set-point: 32°C). The system is ready to
operate.
- In case the setting is wrong, the STANDBY lamp flashes; check the setting of indoor units and the connections of the
refrigerant circuits.
1.Accendere il sistema.
2.Impostare il telecomando dell’unità A come segue (le unità B, C e D devono essere spente):
-Modo di funzionamento: RAFFREDDAMENTO
-Filtro: ON
-Temperatura: 32°C
3.Premere i pulsanti FAN + IFEEL per almeno 5 secondi, indirizzando il telecomando verso il ricevitore posto sul
condizionatore d’aria.
Il sistema parte e funziona per 3 minuti.
Durante questo funzionamento la spia TIMER lampeggia, mentre la spia OPERATION è accesa.
Dopo 3 minuti di funzionamento:
- In caso di impostazione corretta l’unità passa alla modalità RAFFREDDAMENTO e si ferma (temperatura: 32°C). Il
sistema è pronto per il funzionamento.
- In caso di impostazione errata la spia STANDBY comincia a lampeggiare; verificare le impostazioni delle unità interne
e i collegamenti dei circuiti frigoriferi.
1.Mettre en marche le système.
2.Régler la télécommande de l’unité A comme suit (les unités B, C et D doivent être éteintes):
-Mode de fonctionnement: REFROIDISSEMENT
-Filtre: ON
-Température: 32°C
3.Appuyer sur les boutons FAN + IFEEL pendant au moins 5 secondes, en dirigent la commande à distance vers le
récepteur placé sur le climatiseur.
Le système fonctionne pendant 3 minutes.
Pendant ce fonctionnement le voyant TIMER clignote, tandis que le voyant OPERATION est allumé.
Après 3 minutes de fonctionnement:
- Si le réglage est correcte, l’unité change en REFROIDISSEMENT et s'arrête (Température: 32°C). Le système est
prêt pour le fonctionnement.
- Si il y a une erreur dans le réglage, le voyant STANDBY clignote; vérifier le réglage des unités intérieures et les
connexions des liaisons frigorifiques.
1.Schalten Sie das System ein.
2.Stellen Sie die Fernbedienung der Einheit A, wie folgt vorgehen (die Einheiten B, C und D mußen ausgeschaltet
sein):
-Betriebsweise: KÜHLUNG
-Filter: ON
-Temperatur: 32°C
3.Drucken Sie die Taste FAN + IFEEL während 5 Sekunden, indem Sie die Fernbedienung auf den Empfänger auf dem
Klimagerät richten.
Das System arbeitet während 3 Minuten.
Während dieses Betrieb, die Lampe TIMER blinkt, indem die Lampe OPERATION eingeschaltet ist.
3 Minuten nach:
- Wenn die Einstellung ist recht, wählt die Einheit die Betriebsweise KÜHLUNG und sie haltet (Temperatur: 32°C). Das
System ist fertig für das Betrieb.
- Wenn die Einstellung ist falsch, beginnt die STANDBY Lampe zu blinken; prüfen Sie die Einstellung der Inneneinheiten
und die Verbindungen der Kühlrohre uber.
EG
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo ASICS10DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo ASICS10DC in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo ASICS10DC

Argo ASICS10DC User Manual - English - 16 pages

Argo ASICS10DC User Manual - German - 16 pages

Argo ASICS10DC User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info