665480
3
Zoom out
Zoom in
Previous page
1/15
Next page
3
1. Remote control unit.
2. Remote control sensor: Detects the room temperature
around the remote control unit, the air conditioner is
controlled accordingly.
3. Air outlet: Conditioned air is blown out of the air
conditioner through the air outlet.
4.
Air intake: Air from the room is drawn into this section
and passes through air filter which removes dust.
5. Remote control receiver: This section picks up infrared
signals from the remote control unit (Transmitter).
6. Operation selector (without remote control): Push
the button to walk through the operation modes (OFF,
COOL and HEAT)
7. OPERATION lamp: This lamp lights up during
operation.
It blinks once to announce that the remote control
signal has been received and stored.
8. STANDBY lamp: This lamp lights up when the air
conditioner is connected to the power and ready to
receive the remote control command.
9. TIMER lamp: This lamp lights up when the system is
being controlled by the timer.
10. Air filter.
11. Condensate drain connection.
The OFF position does not disconnect the power. Use
the main power switch to turn off power completely.
WARNING
EG
NAME OF PARTS AND OPERATION SELECTOR SWITCH
5
6
7
8
9
3
10
11
2
1
4
NOTA
When the unit receives a signal from the remote
controller, all the three lamps (OPERATION, TIMER
and STANDBY) light up for a moment to indicate the
correct signal reception.
OFF LAMPS FUNTION
It is possible to set the air conditioner in order to let the
OPERATION, TIMER and STANDBY lamps always OFF,
even during operation.
Be sure that the remote controller is ON (using the ON/
OFF button) and that the symbol on the display of
remote controller is OFF, then Press contemporary the
IFEEL and FAN buttons on the remote control unit for more
then 5 seconds.
Repeat the same procedure to set again the normal
operation conditions.
If the air conditioner is powered, but the lamps are off, try
to activate them using this procedure.
In case of troubleshooting the air conditioner diagnostic
system activates the lamps accordingly, even if they are
set to OFF. See paragraph TROUBLESHOOTING for
further details.
The blinking of TIMER and STANDBY lamps and
OPERATION lamp ON, indicates that:
1. Indoor unit has not been addressed.
2. Heating mode has been selected, when the system
was in cooling mode, or vice versa.
Select the correct mode, compatible with the
system.
SEE AUTO-DIAGNOSIS TABLE
MULTI SPLIT SYSTEM
only
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo ADICS13DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo ADICS13DC in the language / languages: English as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo ADICS13DC

Argo ADICS13DC Installation Guide - English, German - 76 pages

Argo ADICS13DC User Manual - German - 15 pages

Argo ADICS13DC Installation Guide - French - 76 pages

Argo ADICS13DC User Manual - French - 15 pages

Argo ADICS13DC Installation Guide - Italian, Portuguese, Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info