765006
11
Zoom out
Zoom in
Previous page
1/124
Next page
Owners Manual - Arctic Spas®
1111
Installation Instructions
Site Preparation
Please ensure the following:
Always put your spa on a structurally sound, level surface. A lled spa can weigh a great deal.
Make certain that the location you choose can support the weight of your lled spa.
• Locate your equipment compartment, which houses all of electrical components, in a place
where you will have easy access for periodic spa care and maintenance.
Allow adequate access to all other doors for service.
Outdoor Ground Level Installation
No matter where you install your new spa, it’s important that you have a solid foundation for support. If
you are installing a spa with a wooden pedestal oor outdoors, we recommend you place patio stones
underneath spaced out evenly. The stones should be at least two inches thick and twelve inches square (30
cm x 30 cm). Even with stones in place, the spa will possibly settle and become uneven, and may require
re-leveling over time. If you are installing a spa with a Forever Floor® outdoors, you may set it on virtually
any surface, as long as it is rm and level.
Deck Installation
To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult
a qualied building contractor or structural engineer. To nd the weight of your spa, its contents and
occupants, refer to the Spa Specication chart. This weight per square foot must not exceed the structure’s
rated capacity, or serious structural damage could result.
Your Arctic Spas® Dealer can help you with local information such as zoning regulations and building
codes.
All Weather Pool Site Prep
Your new All Weather Pool should be placed on a prepared, uniformly solid and level surface (concrete pad,
properly engineered wood deck, etc.). The AWP should not be placed directly on a lawn, bare ground, or
gravel pad due to irregularities in the surface that may cause structural failure of the cabinet and shell that
could void the warranty.
Balconies, concrete pads, and decks should
be constructed to meet all builder codes and
should be able to or exceed supporting 146
Lbs per square foot (7kPa).
Your Arctic Spa is equipped with access
doors on all four sides. It is the customers
responsibility to provide access and ensure
there is a minimum of 24” (600mm) all around
the spa for service person access. Consult
your sales person or service department on the
di󰀨erent ways to achieve this clearance.
WARNING! WARNING!
We recommend that the Arctic Spa be installed
above ground. Consult a licensed building
contractor to design or evaluate your custom
decking requirements. Please ensure access to all
doors on all 4 sides of the spa for serviceability.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arctic Spas Yukon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arctic Spas Yukon in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info