765017
13
Zoom out
Zoom in
Previous page
1/124
Next page
Owners Manual - Arctic Spas®
Startup Procedures
IMPORTANT:
Your Arctic Spa® has been thoroughly tested during the manufacturing
process to ensure reliability and long-term customer satisfaction. Before
lling the spa, wipe the spa shell clean with a soft rag. Make sure to ll
spa through lter bucket.
The following instructions must be read and followed exactly to ensure a
successful start-up or rell.
1) Ensure the electrical connections have been made in accordance with this manual.
2) Ensure all O-Rings have been installed into unions and unions have been tightened
su󰀩ciently.
3) Ensure all ball valves are open, and the drain has been closed. The spas drain tting
located on the external cabinet.
4) Using a garden hose in the lter bucket, ll the spa with pre-ltered water to the bottom
of the pillows (or approximately 6”, 15 cm above the base of the oating weir).
5) Once the spa is lled to the proper level, turn the power to the spa on, by turning on the
GFCI /RCD breaker in your panel.
6) The jet pump, heating system and all internal plumbing will achieve a partial prime as the
spa is lled. To check the operation of the jet system and to remove any remaining air from
the plumbing system, follow these steps:
a) All Models: Push the pump 1 button a second time to turn the pump to high
speed. Allow to run for 1 minute.
b) Signature: Push pump 2 button also. This pump runs at high speed only.
Run for one minute.
c) Legend and Legend Select: Push pump 3 also. This pump runs at high speed
only. Run for one minute.
d) SDS Series push pump 4 button once to turn on and run for one minute. Once the jet
system is fully operational (as indicated by strong, non-surging jets), priming of the
spa is complete. Push each pump button once to turn the pumps o󰀨.
IMPORTANT: Weak or surging jets can be indication of a low water level, or a clogged lter
cartridge.
7) Adjust the chemicals and balance the water according to your dealer’s instructions. A
guideline is also included in this manual, under the Water Maintenance Section.
8) Set the temperature control to the desired temperature (between 100ºF and 104ºF (38ºC
and 40ºC), then place the insulated cover on the spa and allow the water temperature to
stabilize (approximately 16 hours). Make sure you secure the cover in place using the
cover locks. Periodically check the spa water temperature. When the water temperature
climbs above 85ºF (29ºC), proceed to the next step.
1313
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arctic Spas Hudson at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arctic Spas Hudson in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info