765014
86
Zoom out
Zoom in
Previous page
1/124
Next page
1.10.7 Sanitizer and pH Readings
The following provides guidance on the establishment and maintenance of sanitizer and pH readings.
Sanitizer Readings: You should have ORP sanitizer (Chlorine) readings within 24 hours. 24 hours post adding
the salt to the spas water, My Arctic Spa will be able to provide accurate readings regarding the ORP sanitizer
(chlorine) reading, and pH reading.
Important: Always check the pH and ORP (sanitizer) levels before each spa use. If the pH reading is out of
range (to high), adjust accordingly with Arctic Pure, Salt Water Balance to correct it. High pH will cause prema-
ture failure of the Spa Boy Output Electrode, cloudy water, and decreased e󰀨ectiveness of the sanitizer.
* Expect the pH to increase slowly over each week and when the pH gets too high use Arctic Pure, Salt Water
Balance to correct it. High pH will cause premature failure of the Spa Boy Output Electrode, cloudy water, and
decreased e󰀨ectiveness of the sanitizer.
1.11 Caring for your Spa Boy System
Spa Boy Maintenance
Question 1 How do I Replace the Spa Boy Output Electrode? The Spa Boy Output Electrode should be
replaced every 12 - 18 months. Doing this ensures Sanitizer will be produced and sanitizer remains in the
required range. The App also shows a “ BATTERY” displaying the amount of life left in the Spa Boy Salt Cell.
Accuracy of the display is dependent on the salt dosage being within the required range 2000ppm – 2500ppm.
The Spa Boy Output Electrode can be replaced without draining the spas water providing these steps are fol-
lowed.
Steps:
• Turn the breaker o󰀨 to isolate power to your Spa.
• Unscrew the Spa Boy Niche out of its housing.
• Raise the Niche completely out of the spas water and dry o󰀨 any water on the Niche and Electrode.
• To help prevent galvanic corrosion, it is critical to ensure that spa water does not come into contact with the
Spa Boy Electrode Electrical Pin or female matting connection located on the Spa Boy Niche when disconnect-
ing the Niche from the Spa Boy Electrode.
* Keep them high and keep them dry, when replacing the Spa Boy Output Electrode!
• With a small Phillips screwdriver unscrew the set screw that secures the Spa Boy Output Electrode to the
Niche.
• Remove the Spa Boy Output Electrode from the Niche by Unscrewing the Electrode anticlockwise and ensure
the small O-ring has not dislodged from the Electrode and remained behind inside the Niche.
Understanding Spa Boy®
Owners Manual - Spa Boy®
8686
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arctic Spas Eagle at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arctic Spas Eagle in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info