Manual Arcam UDP411 (page 8 of 107) (English, German, Dutch, French, Italian, Spanish)

578728

Zoom out

Zoom in

1/107

E-11E-10

English

e UDP411 is supplied with the CR301 backlit remote

control.

Using the remote control

Please keep in mind the following when using the

remote control:

< Ensure there are no obstacles between the

remote control and the remote sensor on the

front panel. e remote has a range of about 7

metres. (If the remote sensor is obscured, the IR

in remote control input jack on the rear panel is

available. Please consult your dealer for further

information.)

< Remote operation may become unreliable if

strong sunlight or uorescent light is shining on

the remote sensor of the unit.

< Replace the batteries when you notice a reduction

in the operating range of the remote control.

Inserting batteries into the remote control

1. Open the battery compartment on the back of the

handset.

2. Insert two ‘AAA’ batteries according to the

diagram on the battery cover casing.

3. Slide the battery cover casing back into position

and lock it closed with a click.

Backlight

A backlight comes on for ve seconds whenever a key

is pressed. is helps you use the handset in subdued

lighting conditions.

remote

control

NOTE

< Incorrect use of batteries can result in hazards

such as leakage and bursting.

< Do not mix old and new batteries together.

< Do not use non-identical batteries together

– although they may look similar, dierent

batteries may have dierent voltages.

< Ensure the plus (+) and minus (–) ends of

each battery match the indications in the

battery compartment.

< Remove batteries from equipment that is not

going to be used for a month or more.

< When disposing of used batteries, please

comply with governmental or local regulations

that apply in your country or area.

The CR301 remote complies with Part 15

of the FCC rules

is equipment has been tested and found to comply

with the limits for a class B digital device, pursuant to

part 15 of the FCC Rules. ese limits are designed

to provide a reasonable protection against harmful

interference in a residential installation. is

equipment generates, uses, and can radiated radio

frequency energy and if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment o and on, the user is encouraged to try

to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet or a circuit

dierent from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV

technician for help.

basic

operation

Introduction

‘Basic operation’ explains how to play a Blu-ray Disc

(BD), DVD, SACD, CD or other type of disc. Note that

it may be necessary to congure your player correctly

for your system before optimum – or any – playback can

be achieved. Player conguration is described beginning

on page E-16.

More sophisticated features – such as special playback

modes and programming jumps and playback sequences

– are described in the ‘advanced operation’ section, later

in this handbook.

Switching on

Switch the unit on by pressing the POWER button. e

status LED glows green when the unit is powered up and

red when in standby mode. e remote control is used

to enter and exit standby mode. If the POWER button is

pressed (or power is removed) whilst in standby, the

unit will enter standby mode when power is re-applied.

Note that the remote control sensor is located on the

right-hand side of the display window. Do not obstruct

this or the remote control will not work.

Loading a disc

Press

on the front panel (or

on the handset)

and place the disc on the tray, with the playback side

facing down (some discs are double sided, in which case

the side labelled ‘side A’ should face up to play side A).

Press

on the front panel to close the tray. e disc

loads aer a pause of a few seconds.

Playing a disc

A disc may take some time to load once the tray is

closed. When the ‘Optical Disc Autoplay’ setting is set to

On (the default setting), playback starts automatically.

(For details, refer to ‘Optical Disc AutoPlay’ on page

E-17).

If Autoplay is set to O, the player’s Main Menu will

appear on your TV. Use the cursor keys to select the disc

in MY MEDIA, then press

to start playback.

Some titles begin by displaying a menu. Select the menu

item ‘Play movie’ (or similar) using the cursor pad, then

press OK to start playback.

For discs that do not play automatically, press

;

the front panel or press

on the remote control.

Fast play

Press

on the front-panel or remote control to

play fast forwards or backwards. e following speeds

for fast playback are available: x2, x4, x8, x16 or x32

(depending on disc type). Press the button repeatedly

to cycle through the dierent speeds. To resume normal

playback speed, press PLAY.

Skipping chapters/tracks

To skip chapters (or tracks on a CD), press

When skipping back, the rst button press takes you to

the beginning of the current chapter. Pressing the button

again takes you to the start of the previous chapter.

Pausing playback

Press

;

on the front panel or

;

on the remote

control to pause playback. To resume playback, press

;

on the front panel or

on the handset.

Stopping playback

Press the

button on the front panel or

on the

remote control to stop playback.

When playing a BD/DVD, pressing

once performs

a ‘resume stop’. If you now press

, playback resumes

from the point it was stopped.

If you press

on the front panel or

on the remote

control twice, this is a ‘complete stop’, and playback

resumes from the beginning of the disc.

NOTE

When you press a button, if the unit does not accept

its operation,  appears on the TV screen.

Invalid operation may also occur if:

< e region codes of the unit diers from that

of the disc, so playback is not allowed.

< e parental control is set to prevent

operation: see ‘Security/Parental Control’ on

page E-18.

< Some operations may be prohibited due to

disc manufacturer’s settings.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam UDP411 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 8,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam UDP411 Manual

Product: