578739

Arcam SoloBar Manual

8
Zoom out
Zoom in
Previous page
1/115
Next page
E-11E-10
English
Connecting a Solo sub
Being part of the Arcam Solo range means
your Solo sub can communicate wirelessly
with the Solo bar.
Make sure the Solo sub is turned on at its
power switch.
Plug in and turn on
e Solo bar is supplied with a moulded
mains plug already tted to the cable. Check
that the plug supplied ts your supply. If
your mains supply voltage or mains plug is
dierent, please contact your Arcam dealer
immediately.
First, connect the mains cable to the power
socket on the back of the Solo bar, making
sure that it is pushed in rmly. Now push
the plug into your mains socket and switch
the socket on. e unit is now in standby,
indicated by a red LED on the front panel.
If the unit is le unused for an extended
period of time it will go into standby to
reduce power consumption.
Connecting Bluetooth® devices Using headphones
e Solo bar has built in Bluetooth wireless
technology for seamless integration with any
Bluetooth enabled device.
Pairing with Bluetooth devices
Follow the advice provided in the operation
instructions for your Bluetooth device. Select
Arcam Solo bar from the list of Bluetooth devices
to complete the pairing. Once the pairing procedure
is nished, it does not need to be performed again.
e Solo bar comes with a Bluetooth
transmitter so that it can connect to a set of
Bluetooth headphones.
Note: Transmitting via Bluetooth is different
to receiving. Up to four devices can be paired
but only one device can be connected at a
time on a first-come-first-served basis.
Connecting Bluetooth headphones
Press the button on the remote
control followed by until Speaker/
EQ Setup appears on the front display
panel. Press followed by again,
until Headphone Out appears. Press to
selectit.
By default, the Bluetooth transmitter is
turned o so Disable is shown on the display
panel. Press to change the display to
Enabled. e Bluetooth transmitter is now
on and the Device Search menu option is
activated.
Now follow the advice supplied with your
Bluetooth headphones to put them in
pairing mode.
Make sure that Device Search is still
displayed and press . e Solo bar will
search for available devices for one minute.
If no devices are found, press again to
start another search. You might want to
make sure there are no obstacles in the way.
When the search is nished, available
devices will be displayed in a list. Use the
and buttons to select the correct
device and press to nish the pairing
procedure. e Solo bar will display a
message to indicate that the connection has
been successfully completed.
Using your headphones
Make sure both the Solo bar and your
headphones are turned on. Select an audio
source and enjoy listening to sound through
your headphones.
Note: If your headphones are turned off,
audio is automatically played using the Solo
bar speakers.
WARNING: Turning the Bluetooth transmitter on
temporarily disables the Bluetooth input. This
means you will not be able to stream sound from
a Bluetooth device to the Solo bar and listen via
headphones at the same time.
Note: Sync mode lasts for about 30seconds.
If no source is detected during this time, the
Solo bar will stop searching and the process
will need to be repeated.
1. Press the button on the remote
control unit of the Solo bar followed
by until Speaker/EQ Setup appears
on the front display panel. Press
followed by again, until Sub Pairing
appears.
2. Press to start the pairing procedure.
e display will change to In Progress.
3. Position the INPUT selector on the rear
of the Solo sub to WIRELESS.
INPUT
LINE
WIRELESS
LFE
4. Press and hold the WIRELESS button
on the rear of the Solo sub for about ve
seconds. e WIRELESS LED will start
ashing blue, signalling that the Solo
sub is in sync mode and searching for a
source to connect with.
WIRELESS
PAIRING
PWR WIRELESS
5. If the pairing procedure was successful, the
WIRELESS LED will glow a constant blue
and the Solo bar will display Linked.
6. Once the pairing procedure is nished, the
Solo sub will always reconnect whenever it
is powered on or receives an audio signal.
Solo sub
Bluetooth® devices
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam SoloBar at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam SoloBar in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 68,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info