Manual Arcam solo movie 5 1 (page 16 of 30) (English)

371605

Zoom out

Zoom in

1/30

1 6

This section of the document describes the use of

the ‘Set-up’ menu, which allows you to ﬁne-tune Solo

Movie 5.1 to the other items in your system (such as

your video display, speakers and room layout), and to

conﬁgure some personal preferences.

Obtaining a picture

To view the Set-up menu for the initial conﬁguration,

we recommend the use of the composite video

output to connect to your display device. This is

because the high quality video output has several

display modes and may be incompatible with your

display device in its default conﬁguration.

Ensure that your display device is switched on and

that you have selected the correct video input. You

should see the screen shown below. This is the image

that Solo Movie 5.1 gives when there is no disc

playing.

The Display set-up menu

For optimum video performance it may be necessary

to conﬁgure your display for the video source – Solo

Movie 5.1, in this case. A series of test patterns

generated by Solo Movie 5.1 allows you to optimize

colour balance, contrast, brightness and to centre

your picture. Full instructions for each test pattern

are displayed on the screen before the test pattern is

shown.

To enter the Display set-up menu, move the

cursor down to the ‘Display’ button on the screen and

press OK. Follow the on-screen instructions and press

SETUP at any time to quit from a page (or press OK

on the last screen to Exit).

advanced

set-up

Using the Set-up menus

Your Solo Movie 5.1 has two different set-up menus:

The Set-up menu allows conﬁguration of all

aspects of Solo Movie 5.1. Conﬁgurable items

and their potential values are described on the

following pages.

The Display set-up menu is a series of video

test patterns with instructions that help you to

optimize your display for Solo Movie 5.1.

Remember that to use the CR100 remote

control for advanced set-up, you ﬁrst have to

set it to AMP or DVD mode by pressing the

AMP or DVD button.

The Set-up menus

To enter the Set-up menus:

1. Press and hold the front panel

MENU button for

more than one second.

or,

1. Using the remote control, press the

AMP or

DVD button to ensure that the CR100 is in one

of these modes

2. Press the

SETUP button.

You can press MENU (front panel) or SETUP (remote

control) at any time to quit from a page and save all

the settings.

The Set-up menu comprises six pages of options.

– Operation, Video, Audio, Speakers, Delays and Trims.

The tabs on the left side of the screen show the

pages available. To change between pages, move the

menu highlight to the appropriate tab (using the

and

buttons).

To change an item, ﬁrst use the

controls to

highlight the item, then press OK to open the list of

options for the menu item. The current option for the

menu item is ticked. Select a new option using the

controls and conﬁrm the selection with OK.

(If the item to be changed is controlled by a slider,

press OK to activate the slider, move it using the

controls, conﬁrming the setting with OK.)

Note that options that are not currently applicable are

shown ‘greyed out’, and cannot be highlighted or changed.

Screen saver

To protect your screen from damage from a

persistent static image, a screen saver starts after a

few minutes of inactivity.

An Arcam logo appears at random locations around

the screen. To restore the previous screen image,

press the

(stop) button on the front panel or the

remote control.





Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam solo movie 5 1 in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam solo movie 5 1

Arcam solo movie 5 1 User Manual - German - 30 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam solo movie 5 1 Manual

Product: