Manual Arcam solo movie 2 1 (page 16 of 30) (English)

160350

Zoom out

Zoom in

1/30

E-16

Balance

Balance allows you to increase the volume of one

channel (left or right) relative to the other. Altering the

balance may help to restore the stereo image for an off-

centre listening position.

Bass

This setting boosts the lower frequency components of

your music. If your music is not ‘warm’ enough, increase

this setting; if your music is ‘boomy’, decreasing this setting

may help. See also ‘Bass correction’, below.

Treble

This setting changes the relative volume of the higher

frequency components of your music. If you feel that

percussion items in the music (for example) are being

lost, increasing this setting may help. If high frequency

sounds are too dominant, decrease this setting.

Bass Correction

This setting should normally be left on minimum. Bass

correction may be used if Solo Movie 2.1 is connected

to limited-frequency-range (‘Small’) speakers, that cannot

reproduce very low frequency sounds. Increasing this

setting progressively increases very low frequency bass.

This control should not be used at high volumes as it

may damage your speakers.

Sub Level *

This adjusts the level of the

SUB (subwoofer, or LFE

speaker) pre-amp output relative to the other two

channels. Sub level does not apply to headphone output.

Sleep Timer

This timer allows you to specify a listening period, after

which Solo Movie 2.1 will switch automatically into

stand-by. The period can be set in 5-minute intervals, up

to 120 minutes (2 hours).

FM Mode

(This menu item is shown only when the selected source

is FM.)

In some weak signal areas, it can be beneﬁcial to force

the FM tuner to mono output, as mono requires a much

lower signal strength to produce acceptable results. If the

signal strength in your area is good, leave this as ‘stereo’.

DAB Setup

(This menu item is shown only when the selected source

is DAB.)

There are two options under this menu item – ‘Scan’ and

‘Erase settings’. Selecting ‘Scan’ causes Solo Movie 2.1 to

search for new DAB stations. If any are found, then they

will be added automatically to the list of available stations.

Scanning for new stations does not erase old stations

that are no longer transmitted – over time, or if you

change location, this may lead to you having a number

of stations in your list that cannot actually be received. In

this case, select ‘Erase settings’, then perform a new scan;

when the scan is complete, only stations that are available

currently in your area will be shown.

Set Preset

(This menu item is shown only when the selected source

is DAB, FM or AM.)

This allows you to store a radio station that you have

tuned in to as a numbered preset (conﬁrm with

OK).

The station can then be retrieved by pressing the preset

number on the remote.

In the same way, you can erase a particular numbered

preset (conﬁrm with

OK).

See the section ‘Setting station presets’ on page 25 for

more information.

iPod Option

(This menu item is shown only when the selected source

is AUX.)

The default setting is ‘Disabled’, but if you intend to use

Arcam’s rDock or rLead accessories to integrate an

iPod

with your system, you should set the appropriate

option. Connect the rDock or rLead to the rear of

the unit (full details are given in the quick start guides

supplied with the accessory units) and Solo Movie 2.1

will test for the presence of a connected iPod. Solo

Movie 2.1 takes over the control and ampliﬁcation of the

source, with iPod text displayed on the front panel of the

system unit.

Amplifier menu settings

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam solo movie 2 1 in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam solo movie 2 1

Arcam solo movie 2 1 User Manual - German - 30 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam solo movie 2 1 Manual

Product: