578726
11
Zoom out
Zoom in
Previous page
1/107
Next page
E-17E-16
English
Bi-amping
Bi-amping requires the use of two ampliers per
channel. Normally, your A49 is used to drive the high-
frequency (treble) speakers, while a power-amplier
(such as a P49/P349) is used for the lower (bass)
frequencies.
Connect your A49 to the speakers as described for
single wiring, with the exception that the A49 should be
connected to the speaker terminals labelled HF or ‘High
Frequency’.
en connect the power amplier (P49/P349, for
example) to the LF or ‘Low Frequency’ terminals, as in
the diagram. A pair of audio interconnect cables are also
required to connect the pre-amp outputs of the A49 to
the power amp inputs of the P49/P349.
e interconnects can be either XLR (recommended for
longer cable runs) or phono (RCA). Set the INPUT switch
on the P49/P349 to the appropriate setting for the cables
used.
WARNING: the strip of metal on the speakers connecting
the low frequency (LF) terminals to the high frequency (HF)
terminals MUST BE REMOVED. Failure to do so will result
in damage to both ampliers, which will not normally be
covered under warranty.
To allow the power state of the P49/P349 to be
controlled by the A49 please connect the TRIGGER OUT
to the TRIGGER IN using a mono 3.5mm jack lead – not
supplied.
An A49 and P49 connected to speakers using bi-amping.
PHONO
GROUND
ONLY
PHONO
(MM)
CD TUNER SAT BD PVR AV
RECORD
OUT
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
AUX R AUX L PRE OUT R PRE OUT L
TRIGGER OUT
6V 1A 12V 1.5A
ACCESSORY
POWER
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
25dB/31dB
GAIN
L
R
PRE
IN
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
PRE IN R PRE IN L
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
TRIGGER IN
TRIGGER OUT
LF
HF
LF
HF
R L
A49
P49
Remove
metal strip
Remove
metal strip
Make sure INPUT
switch matches wired
configuration (XLR or RCA)
Make sure MODE
switch is set to ST
Make sure GAIN
switch is set to 31dB
NOTE: Units can be interconnected via XLR or RCA.
Both versions shown for illustration purposes only.
ST/BRIDGE/DM
MODE
ST/BRIDGE/DM
MODE
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
XLR/RCA
INPUT
25dB/31dB
GAIN
25dB/31dB
GAIN
LF
HF
LF
HF
Bridged mode - P49 only
In bridged mode only the L+ and R+ outputs of SPEAKER
1 are active.
WARNING: Do not make any connections to the other speaker
terminals, doing so will severely damage your amplier.
If each speaker has more than one pair of connecting
terminals, use the terminals labelled LF or ‘Low
Frequency’.
To drive your right speaker, select one of the P49
ampliers and connect the red positive speaker terminal
labelled SPEAKER 1 L+ to the positive LF terminal of your
right speaker.
R
A C49 pre-amp and two P49 power amps in bridged configuration.
PHONO
GROUND
ONLY
PHONO
(MM)
CD TUNER SAT BD PVR AV
RECORD
OUT
PRE
OUT
AUX R AUX L PRE OUT R PRE OUT L
TRIGGER OUT
6V 1A 12V 1.5A
ACCESSORY
POWER
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
25dB/31dB
GAIN
L
R
PRE
IN
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
PRE IN R PRE IN L
TRIGGER IN
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
TRIGGER OUT
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
25dB/31dB
GAIN
L
R
PRE
IN
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
PRE IN R PRE IN L
TRIGGER IN
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
TRIGGER OUT
L
Similarly, connect the red positive speaker terminal
labelled SPEAKER 1 R+ to the negative LF terminal of your
right speaker.
Repeat the above procedure to connect the second P49
amplier to the le speaker.
WARNING: Make absolutely sure you have used the correct
SPEAKER 1L+ and R+ terminals.
In this setup only one interconnect is required to each
power amplifer and it should be connected to the PRE
IN L input.
C49
P49 P49
e interconnects can be either XLR (recommended for
longer cable runs) or phono (RCA). Set the INPUT switch
on the P49 to the appropriate setting for the cables used.
WARNING: If your speakers support bi-wiring, there will be a
strip of conductive metal connecting the low-frequency (LF)
terminals to the high-frequency (HF) terminals; this MUST NOT
BE REMOVED in a bridged mode system.
To allow the power state of the P49 to be controlled by
the A49 please connect the TRIGGER OUT to the TRIGGER
IN using a mono 3.5mm jack lead – not supplied.
Make sure MODE
switch is set to BRIDGE
on both amps
ST/BRIDGE/DM
MODE
ST/BRIDGE/DM
MODE
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
XLR/RCA
INPUT
25dB/31dB
GAIN
25dB/31dB
GAIN
NOTE: Units can be interconnected via XLR or RCA.
Both versions shown for illustration purposes only.
Make sure INPUT
switch matches wired
configuration (XLR or RCA)
on both amps
ST/BRIDGE/DM
MODE
ST/BRIDGE/DM
MODE
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
XLR/RCA
INPUT
25dB/31dB
GAIN
25dB/31dB
GAIN
Make sure GAIN
switch is set to 31dB
on both amps
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam P349 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam P349 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info