Manual Arcam P349 (page 10 of 107) (English, German, Dutch, French, Italian, Spanish)

578726

Zoom out

Zoom in

1/107

E-15E-14

English

AMP Device Mode

e A Device Mode button congures the CR902 to

control your Arcam amplier. Pressing this button does

not aect the currently selected input on the amplier.

Toggles power between standby and on

DISP

Cycles through the front panel display’s

brightness options

Displays the amplier setup menu on the

front panel

Navigate menus

conrms a selection

Toggles the mute function of the amplier

VOL-

VOL+

Decrease () and increase (+) amplier

volume

SP1

Toggles Speaker 1 output

SP2

Toggles Speaker 2 output

BAL

Adjusts the balance between the le and

right audio channel

TUN Device Mode

e T Device Mode button congures the CR902 to

control the tuner functions of Arcam tuners.

Toggles power between standby and on

…

e numeric keys are used to store and

recall presets

DISP

Cycles through the front panel display’s

brightness options

INFO

Cycle through dierent information

display modes

)

Rewind iPod

(

Fast forward iPod

]

Preset down/Sirius category down/iPod

track back

[

Preset up/Sirius category up/iPod track

forward

Stop iPod

Play / pause iPod

Displays the tuner setup menu on the front

panel

' ,

Preset up / down, iPod track back / forward

< >

Decrement / increment tuning frequency

Conrm a selection

FM MONO

Toggle FM mode between mono and stereo

reception

P/TUNE

Enter/Exit Preset recall mode

STORE

Enter/Exit Preset store mode

BAND

Cycles through available tuner bands

CD Device Mode

e c Device Mode button congures the CR902 to

control the CD functions of Arcam CD players.

Toggles power between standby and on

Open/close disc tray

…

e numeric keys allow direct access to

individual tracks on a disc. To select a track

press the corresponding keypad button.

For tracks greater than 9, enter the digits

in sequence. For example, to play track 15,

press

, then press

DISP

Cycles through the front panel display’s

brightness options

MODE

Changes the available display modes on the

CD player

)

Fast rewind

(

Fast forward

]

Skip back to the start of the current/

previous track

[

Skip forwards to the start of the next track

Stop playback

Play

Toggles pause of playback

Enter a track in a programmed track list

Navigates track listings if supported by the

player

selects the currently highlighted track if

supported by the player

SHUFF

Toggles random (‘shue’) play on and o

RPT

Repeat playback of the disc or pre-

programmed selection of tracks. To repeat

a particular track, select that track and press

RPT twice. To cancel, press RPT a third time.

SACD

Toggles between selecting the HD and CD

layer of SACD disc

BD Device Mode

e B Device Mode button congures the CR902 to

control the BD functions of Arcam BD players.

Toggles power between standby and on

Open/close disc tray

…

e numeric keys allow direct access to

individual tracks on a disc. To select a track

press the corresponding keypad button.

For tracks greater than 9, enter the digits

in sequence. For example, to play track 15,

press

, then press

DISP

Cycles through the front panel display’s

brightness options

MODE

Changes the available display modes on the

BD player

)

Fast rewind

(

Fast forward

]

Skip back to the start of the current/

previous track

[

Skip forwards to the start of the next track

Stop playback

Play

Toggles pause of playback

AUDIO

Changes audio decode format (Dolby

Digital, DTS, etc.).

Activates BD player menu.

Navigates track listings if supported by the

player

selects the currently highlighted track if

supported by the player

Returns navigation to the top level of the

menu (‘Home’).

RTN

When navigating a menu, press this key to

return to the previous screen or selection

SHUFF

Toggles random (‘shue’) play on and o

RPT

Repeat playback of the disc or pre-

programmed selection of tracks. To repeat

a particular track, select that track and press

RPT twice. To cancel, press RPT a third time.

SACD

Toggles between selecting the HD and CD

layer of SACD disc

loudspeakers

Normal single wiring

For single wiring, we recommend that you use the

SPEAKER 1 set of terminals on your amplier. If each

speaker has more than one pair of connecting terminals,

use the terminals labelled LF or ‘Low Frequency’.

Connect the red positive terminal of the right speaker

connection on the amplier (labelled R+) to the positive

terminal of your right speaker. Similarly, connect the

black negative terminal of the right speaker connection

on the amplier (labelled R) to the negative terminal

of your speaker. Repeat the process for the le speaker,

using the terminals labelled L+ and L on the amplier.

WARNING: If your speakers support bi-wiring, there will be a

strip of conductive metal connecting the low-frequency (LF)

terminals to the high-frequency (HF) terminals; this MUST NOT

BE REMOVED in a single-wired system.

Notes on making speaker connections

< Do not make any connections to any amplier while it is switched on. We recommend that your

amplier is completely disconnected from the mains supply before starting.

< Before switching your amplier(s) on for the rst time aer connecting to speakers, please check all

connections thoroughly. Ensure that bare wires or cables are not touching each other or the amplier’s

chassis (which could cause short circuits), and that you have connected positive (+) to positive and

negative (–) to negative. Be sure to check the wiring for both the amplier and the speaker.

< Aer making connections: switch the amplier(s) on, select a source signal, then gradually increase the

volume to the required listening level.

< If you are unsure as to how your system should be connected, or need advice on bi-amping, please

contact your Arcam dealer who will be happy to help you.

Connecting

loudspeakers

ere are many dierent ways of connecting your

loudpeakers to your A49 or P49/P349 and the following

section describes how to connect and congure the

loud speakers and amplier for the most common

congurations.

PHONO

GROUND

ONLY

PHONO

(MM)

CD TUNER SAT BD PVR AV

RECORD

OUT

PRE

OUT

4–16 OHMS. CLASS 2 WIRING

SPEAKER 1 SPEAKER 2

4–16 OHMS. CLASS 2 WIRING

SPEAKER 2 SPEAKER 1

AUX R AUX L PRE OUT R PRE OUT L

TRIGGER OUT

6V 1A 12V 1.5A

ACCESSORY

POWER

110-120V/220-240V

~ 50-60 Hz

350W MAX

POWER INLET

SUPPLY

VOLTAGE

SWITCH POSITIONS

115 = 110 - 120V~

230 = 220 - 240V~

A49

An A49 connected to speakers using single wiring.

R L

Bi-wiring

Bi-wiring is performed in the same way as single wiring

except that, a pair of cables are used to connect the

amplier to each speaker.

Follow the instructions given for single wiring; then

perform the same actions, this time connecting the

SPEAKER 2 set of terminals on your amplier to the

terminals labelled HF or ‘High Frequency’ for each

speaker.

WARNING: Speakers that support bi-wiring have a strip of

metal that connects the low frequency (LF) terminals to the

high frequency (HF) terminals. This MUST BE REMOVED in a

bi-wired system.

PHONO

GROUND

ONLY

PHONO

(MM)

CD TUNER SAT BD PVR AV

RECORD

OUT

PRE

OUT

4–16 OHMS. CLASS 2 WIRING

SPEAKER 1 SPEAKER 2

4–16 OHMS. CLASS 2 WIRING

SPEAKER 2 SPEAKER 1

AUX R AUX L PRE OUT R PRE OUT L

TRIGGER OUT

6V 1A 12V 1.5A

ACCESSORY

POWER

110-120V/220-240V

~ 50-60 Hz

350W MAX

POWER INLET

SUPPLY

VOLTAGE

SWITCH POSITIONS

115 = 110 - 120V~

230 = 220 - 240V~

A49

An A49 connected to two sets of speakers using bi-wiring.

R L

Remove

metal strip

Remove

metal strip

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam P349 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam P349 Manual

Product: