578752
5
Zoom out
Zoom in
Previous page
1/16
Next page
C31/P38/P1
E-4
English
C31/P38/P1
E-5
Recording loops
The C31 is equipped with two recording loops, for use with recording devices (such as cassette decks,
MiniDisc players, VCRs etc.)
7
TAPE/PROC RECORD OUT – Connect these output sockets to the input sockets of your recording
device (usually labelled RECORD or IN).
8
TAPE/PROC PLAY IN – Connect the output sockets of your recording device (usually labelled PLAY
or OUT) to these inputs.
If you do not have a recording device, you can use this input for other (line-level) equipment, such
as a CD-player, tuner, VCR, etc.
9
VCR/TAPE2 RECORD OUT – These output sockets can be connected to the input sockets of a
second recording device.
bk
VCR/TAPE2 PLAY IN – Connect the output sockets of your second recording device to these
inputs. Alternatively, this input may be used for other (line-level) equipment such as a CD-player,
tuner, etc.
Power-amplier connections
456
PRE OUT – The recommended connection between the C31 pre-amplier and your power
amplier depends on both the distance between the two and the type of power amplier that you are
using. There are three options:
1. If the cables to be used to connect the C31 to the power amplier are less than 3m long, we
recommend connecting the DIRECT sockets
6
to the input sockets of your power amplier. On the
P38 and P1, connect to the socket(s) labelled AUDIO IN.
If the cables to be used to connect the C31 to the power amplier are 3m or longer, then the connection
to use depends on the type of power amplier you have.
2. If your power amplier does not have balanced inputs (such as the P38), use the BUFFERED
outputs
5
. On the P38, connect to the sockets labelled AUDIO IN.
3. If your power amplier provides balanced inputs (such as the P1), use the balanced outputs
4
. On
the P1, connect to the sockets labelled BALANCED AUDIO IN.
The buffered and balanced outputs are designed to drive longer cables than the direct output, but you
cannot damage either your C31 or your power amp. by using the “wrong” connection type.
Other connections
Phono earth terminal – For connecting your turntable earth lead (if required). Note that this terminal
must not be used as a safety earth.
3
TRIG OUT and REMOTE IN (12V in and out) – These connections are intended for use in multi-
room installations.
n
TRIG OUT: This output provides a 12V signal whenever the unit is switched on (i.e.,
not off or in stand-by). This signal can be used to switch on power ampliers (or other
equipment) connected to the C31, as they will come on when the C31 is activated. This is
useful if the power amplier is remote from the C31, or otherwise difcult to access.
n
REMOTE IN: This allows remote-control signals to be received by the C31 if the remote
sensor is covered (or otherwise not ‘visible’ to the remote-control). An external sensor
(such as the Xantech ‘Dinky Link’™) is used to receive the signals from the remote-control,
which are then fed to the C31 (into this input) using a suitable cable.
In normal use there is no need to make any connections to either of these sockets.
Connecting to a power supply
Mains lead
The appliance is normally supplied with a moulded mains plug already tted to the lead. Check
that the plug ts your supply and that your mains supply voltage agrees with the voltage
setting (115V or 230V) indicated on the rear panel of the unit
2
before plugging in.
If your mains supply voltage or mains plug is different, please consult your Arcam dealer
immediately.
Plugging in
Push the IEC-plug of the power cable into the socket POWER INLET
1
in the back of the unit,
making sure it is pushed in rmly.
Stand-by power
For remote stand-by operation, the amplier’s control power-supply is kept powered up all the time the
unit is connected to the mains supply. The front-panel power-switch powers all other circuitry down and
power consumption in this mode is less than 2W.
This means that even though the power-switch is off, it may be possible to hear a slight residual hum
coming from the mains transformer inside the amplier. This is perfectly normal. If the unit is to be left
unused for an extended period, however, we recommend that it is disconnected from the mains supply.
The 12V-trigger uses
a 3.5mm mono jack
plug, wired as follows:
n
Sleeve: Ground
n
Tip: Active
When the C31 is
powered-on, the tip
carries 12V, current-
limited to 30mA; other-
wise the tip carries 0V.
The remote-in also uses
a 3.5mm mono jack
plug, wired as above.
Remote control signals
must be in modulated
RC5 format, with a
voltage level of 5–15V.
Note that the remote
receiver will require its
own power-supply.
Details of the
Xantech ‘Dinky Link’
can be found at
www.xantech.com, or
ask your dealer.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam P1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam P1 in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam P1

Arcam P1 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info