578807

Arcam Neo Manual

6
Zoom out
Zoom in
Previous page
1/88
Next page
E6
>60cm
15 –
40cm
40 – 60cm
2 – 3m
Speaker installation
The advice given here are general guidleines for speaker installation.
Refer to the documentation supplied with your speakers for more
precise positioning and installation information.
Positioning
As a rough guide, speakers should be placed on rigid stands at about
15–40cms from the rear wall and at least 60cms from any side wall.
Speakers should never be placed on the oor (unless they are oor-
standing speakers), or in corners.
The nal sound will depend on the acoustics of the listening room
and experimentation with speaker positioning is very worthwhile.
As a starting point, we suggest that the speakers are placed
2–3m apart with their backs 15cms from the rear wall.
Listening in a second room
Solo Neo provides two independent volume
controls, oering you the possibility of listening
to the same output in two dierent rooms of your house. To do this, you will require the
following:
< a power amplier (such as the Arcam P38) and speakers;
< suitable interconnect cables, such as those described above;
< a remote control receiver (optional), available from your Arcam dealer;
< a second Solo Neo remote control (optional), available from your Arcam
dealer.
Make the connections as follows:
1. Ensure that all equipment is switched o and disconnected from the mains
supply.
2. Connect the outputs of Solo Neo labelled ‘Zone 2’ to the audio inputs of the
power amplier using the interconnect cables.
3. Connect the speakers to the speaker terminals of the power amp. The speakers should
be connected in the same method as described in the panel on page 4, ‘Speakers’.
4. Plug the remote receiver from the second room into the connector labelled ‘In Zone 2’
on the rear of Solo Neo.
5. Reconnect the equipment to the mains supply and switch on. You should be able to
hear the output of Solo Neo in through the power amp. and control the volume using
the remote control.
Adjusting Zone 2 volume
Press and hold MENU on the front panel until ‘Z2 Vol’ is displayed, then use the volume
control to decrease/increase the Zone 2 volume. Press MENU again to exit.
Note that the second room is always muted when
Solo Neo is switched on – it must be unmuted
‘explicitly’ when required. This is to avoid
unexpected output in the remote location.
Speaker stands
The more rmly a speaker is held, the better it will sound. We
recommend the use of rigid metal stands of 40–60cms height.
Properly damped types that do not ‘ring’ when tapped with
a pencil (either by virtue of construction, or because they are
lled with dry silver sand) will bring out the best in a speaker.
Ensure that the stands and/or speakers do not wobble.
>60cm
15 –
40cm
40 – 60cm
2 – 3m
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam Neo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam Neo in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info