578800
11
Zoom out
Zoom in
Previous page
1/14
Next page
2120
The following modes will be available: Stereo, Dolby Digital, DoIby
Pro Logic, Dolby 3 Channel, DTS, Digital Stereo.
Note:
Some modes may be disabled dependant on the actual input signal.
Modes can be selected by use of the front panel MODE
button or the MODE buttons on the remote handset.
The modes that are selectable are dependant on the actual source
material being played.These are shown below:
PCM DIGITAL INPUT(CD SIGNAL): Digital stereo, Dolby
Pro Logic Digital, DoIby 3 Channel (if no rears are selected).
DOLBY 2 CHANNEL: Dolby Digital Stereo, Dolby Digital Pro
Logic, Dolby Digital 3 channel (if no rear speakers are selected)
DOLBY MULTI CHANNEL: Dolby Digital stereo mx (mix
down), Dolby Digital XXX eg 3/2/.1
DTS 2 CHANNEL: DTS Digital Stereo
DTS MULTI CHANNEL: DTS Digital Stereo Mx, DTS Digital
XXX
ANALOGUE: Stereo analogue, Dolby Pro Logic - analogue,
Dolby 3 Channel (if no rear speakers are selected).
Source material, particularly DVDs, will vary from disc to disc in
the number of surround channels encoded. Frequently, you may
find only stereo has been encoded, particularly on older movies.
Below are some of the more commonly available formats.
If you wish to listen to a source that is not a 2 channel stereo
source you MUST change the mode to a stereo mode in order to
hear all of the sound correctly on the headphones. For example if
you are listening to a DVD player in 5.1 channel mode you would
have to set the mode to Dolby Digital Stereo mixdown when
listening on headphones. If you don’t you will not be able to hear
any of the main dialogue signals on your headphones because this
is a centre channel signal.
Adequate ventilation MUST be provided for the DAVE amplifier,
and it is strongly recommended that it is not stacked with other
products, particularly additional power amplification.
The DAVE surround decoding circuitry requires a temperature
controlled environment in which to function correctly. If the
internal temperature of the unit reaches a certain point, a cooling
fan will begin operating to cool the circuitry.You may hear this as a
very quiet whirring sound coming from the amplifier.This is normal.
If the temperature continues to rise the amplifier may shut itself
down to allow it to cool. If this happens the unit will switch into
standby mode and ‘Fault Condition Protection’ will be shown on
the display. When the unit has cooled down sufficiently the unit will
automatically switch out of standby again.
In addition, fan cooling is also provided for the two main output
channels.This cooling is only activated above a certain
temperature, and when there is a signal present, so any fan noise
will be masked as far as possible, by the loudspeaker output.
It is only possible to record from an analogue source.You cannot
record from any digital source. If you wish to record from a CD
player connected to one of the digital inputs you will have to make
a connection from the analogue outputs of the CD player directly
to your recorder or to the analogue CD inputs of the Alpha 10.
In the latter case you can then record the CD signal by pressing
the front panel RECORD button followed by the CD input button.
To record from a laser disc player connected to the AV analogue
inputs of the amplifier first press the RECORD selector followed
by the AV button.This will route the audio signals of the Laser Disc
to the VCR Audio Record Out sockets and the video signal to the
composite or S Video VCR OUT socket (S Video, Composite
video). Note: you may not be able to record the video signal if it
contains Macrovision copy prohibit signals.
The amplifier will automatically switch to the best source signal
when an input is selected if DECODE mode has been set to
'AUTO'. For example if you have a CD player connected to the
digital input and also an analogue connection to the CD inputs the
unit will default to the digital signal when CD is selected.To force
the unit to the analogue input press and hold the CD button until
Analogue is shown on the OSD or front panel display.This will take
about 4-5 seconds. If you press the CD button again it will reselect
the CD digital input signal.
DAVE amplifier - Advanced features
MODE SELECTION VENTILATION
MULTICHANNEL MODES
TAPE RECORDING
LISTENING TO AN ANALOGUE OUTPUT
LISTENING ON HEADPHONES
Source material Displayed as Alternative
signal type description
Mono mono -
Left+Right stereo -
Left+Right Pro Logic encoded Surround ‘Digital Pro Logic’
Centre+Left+Right+Surround (mono) Digital 3/1/0 ‘Digital 4.0’
Centre+Left+Right+Surround L, R Digital 3/2/0 ‘Digital 5.0’
Centre+Left+Right+Surround L, R & LFE Digital 3/2/.1 ‘Digital 5.1’
DAVE amplifier - Remote Control Handset
PHONO
1
CD
4
DVD
7
SYSTEM
+10
AUX TUNER
MUTE
GUIDE
EXIT
PRE
CH
MENU
T/V
POWER
SAT
AUD
TV
CD
VCR
VOL CH
DVD
CBL
AUX
2
TAPE 1
5
VCR
8
CHECK
0
R
E
W
F
F
3
AV
6
SAT
9
SHIFT
M3
LIGHT
M4M1 M2
ENTER
RESTORE
FAV
DISPLAY
1
FUNCTION
1
TEST
EFFECT
230V
MODEREARTRIMSELECT-
NIGHT
ALT
PAUSE
STOP
SEL
PLAY
ARCAM
LEARNING REMOTE CONTROL
2 43
5 6 87
1
9
12 14
21 22
23
16
17
19 18
20
24
13 15
25 26
28 29
31 32
35
41 42 43 44 46
46
51 52 53
55
54
47 48 49 50
34
1110
27 37
30 38
33 39
36 40
The CR 9000 Programmable and learning Remote Control
Handset is supplied with the DAVE amplifier.
This Remote Control Handset can be programmed to send
messages to other devices in your home entertainment system.
The Remote Control therefore has a universal numbering system
to cross reference a button to a function.
This is required as the words printed on the Remote Control and
the programmed functions may not be the same.
Refer to the CR 9000 Operating Manual for full instructions.
The adjacent diagram will help you to acccess the functions of
other equipment using the universal reference numbers in the
Operating Manual supplied.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam FMJ P25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam FMJ P25 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info