159827

Arcam fmj ms250 Manual

32
Zoom out
Zoom in
Previous page
1/36
Next page
MS250
32
If you do wish to ‘share’ the internet connection on your PC with the MS250, you can do this as follows:
1. Using an Ethernet crossover cable (not a straight-through cable), connect the MS250 to the
computer’s ethernet port
2. Enable Internet Connection Sharing on your computer
3. Switch on the MS250.
You can also use a wireless connection between the MS250 and your computer. To do this, you will need
two wireless Ethernet Bridges. These will need to be congued using your PC, then connect one to your
computer, and one to the MS250.
If you don’t have an Ethernet network or an ADSL or cable modem
The easiest way to establish an Ethernet network with Internet connection for your MS250 is to use an
ADSL or Cable Router connected to your PC. To simplify the wiring, you may prefer to
use a wireless ADSL or Cable Router and a wireless Ethernet Bridge connected to the
MS250. Proceed as follows:
1. Subscribe to a broadband service and specify that you would like to use a
wireless ADSL or cable Router. Many ISPs can provide a suitable router when
you sign up; if not, you will need to purchase one of these from a computer
store.
2. Connect your computer to the router.
3. Congure the router according to the instructions provided with it and the
conguration information provided by your ISP.
4. If you are using a wired Ethernet conguration, connect the MS250 to a spare LAN port
on the Ethernet Router using a straight-through Ethernet cable. Refer to the diagram under
‘Connecting the MS250 to an existing Ethernet network with Internet access’.
or
If you are using a wireless Ethernet conguration, use your PC to congure the Wireless
Ethernet bridge according to the instructions provided with it and then connect the Wireless
Ethernet bridge to the MS250. Refer to the diagram above.
5. Switch on the MS250.
Connecting the MS250 to the Internet without a computer.
Although it is usually necessary to use a computer to congure the modem in the setup described above,
once the conguration has been completed you no longer need the computer to access Internet radio
stations or retrieve track names for CDs. The computer can therefore be disconnected, leaving only a
single connection between the ADSL/cable router and the MS250.
Testing your Internet connection
To check that the MS250 is able to use your broadband Internet connection:
1. Insert an audio CD into the MS250’s CD drive.
2. Check that the MS250 retrieves track names from the Internet.
It may take a few moments to recover the track names from the Internet database. Also, although track
names for most CDs are available, there are a few exceptions. Try another CD before concluding that the
Internet connection is at fault.
Advanced network conguration information
By default, the MS250 is conguret to use DHCP, which means that it will pick up its network settings
automatically from a suitable device (normally the router) on your LAN. However, if your network does
not use or support DHCP, you will need to congure the MS250 with a static IP address. To do this, you’ll
need to know the following settings (either obtain them from your ISP, or congure them to t in with
existing network setup):
1. From the Home page, select Settings
)
Network
)
Ethernet
2. From the NETWORK-ETHERNET menu screen, enter the following information:
IP Address – this must be a unique address on your LAN (e.g. if your router has the IP address
192.168.1.1, you might set the MS250’s IP address to be 192.168.1.101)
Subnet mask – this must match the subnet mask of other devices on your LAN (and is usually
255.255.255.0)
Name server – this is the IP address of the device that converts domain names into appropriate
IP addresses and vice versa (normally the address of your router)
Gateway – the IP address of the device on your LAN that acts as a gateway to the Internet and
other networks (this is normally your router)
3. Make sure that Settings
)
Network
)
Options shows that DHCP is disabled.
4. Select ‘Apply’ to enact the new network settings (this will take a few moments).
MS250
POWER
LOAD
OKHOME ZONE
DISPLAY








NOTE
Although the MS250 has a total of
three USB ports, you cannot connect
a USB modem to the unit directly.
The USB ports are for use with
an external archive disk and/or a
keyboard.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam fmj ms250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam fmj ms250 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info