578767
9
Zoom out
Zoom in
Previous page
1/19
Next page
AVR200
9
English
1 INPUT SETTINGS
2 CHANNEL BALANCE
3 CHANNEL DELAYS
4 SPEAKER SETTINGS
5 EXIT
SETUP
LEFT : 0dB
CENTER : 0dB
RIGHT : 0dB
REAR L : 0dB
REAR R : 0dB
SUB : 0dB
DO NOT SAVE AND EXIT
SAVE AND EXIT
CHANNEL BALANCE
NOTE: The test tone generates a noise which may not be
heard through a subwoofer. To set your sub to a suitable
level, turn off the test tone and experiment with the trim
while playing a piece of music or a movie you are familiar
with. There is no right or wrong level for the sub: simply nd
the balance that is best for you.
1 INPUT SETTINGS
2 CHANNEL BALANCE
3 CHANNEL DELAYS
4 SPEAKER SETTINGS
5 EXIT
SETUP
CENTER 0ms
REAR 0ms
DO NOT SAVE AND EXIT
SAVE AND EXIT
CHANNEL DELAYS
CENTER 3ms
REAR 6ms
DO NOT SAVE AND EXIT
SAVE AND EXIT
CHANNEL DELAYS
NOTE: It is not necessary to adjust delay times separately
for a DTS (Digital Theater Systems) source.
DIMENSION (Dolby Pro Logic II Music Mode only) Allows
the gradual adjustment of the sound eld either
towards the front or the rear. This can help
achieve the desired balance from all the
speakers with certain recordings that may
contain either too much or too little spatial
effect. Step 0 is the recommended setting,
which has no effect on the sound. Steps
+1, +2 and +3 gradually move the sound
forward, and steps ‘–1, ‘–2 and ‘–3 move the
sound towards the surrounds.
Channel balance page
From the Channel balance page, you can trim the level of
each individual loudspeaker connected to the AVR200. Due to
the different performance characteristics or positioning of each
loudspeaker they may need to be set to different levels to
provide a balanced sound from the listening position. To help set
this balance, the AVR200 can generate a test tone that plays an
identical signal through each channel in turn. Trim the balance
of each speaker in turn until they all appear to produce the
same volume.
Once the channel balance page is shown in the OSD, press
the
TEST button on the remote control to start the test tone.
Make sure that either Dolby Digital, Dolby Pro Logic or Dolby
Pro Logic II is selected, and that the volume on the AVR200
is set suf ciently high for the tone to be heard. The test tone
automatically cycles through each speaker channel until the
TEST button is pressed a second time.
Each loudspeaker can be trimmed between +10dB and 10dB.
You can return to the Channel balance page at any time (without
rst entering the OSD) by pressing the
TEST button on the
remote control. Press TEST again to exit this page.
Channel delays page
For best results in a surround sound system, the sound from
all loudspeakers should reach the listener at the same time. To
help achieve this the AVR200 can add slight delays to certain
channels when in Dolby Digital or Dolby Pro Logic modes.
When playing a Dolby Digital source you can set a delay for the
centre channel of between 0 and 5ms and a delay for the rear
channels of between 0 and 15ms.
The method of calculating these delay times is described
overleaf.
Setting options for DIMENSIONS
DISPLAY EFFECT
3 MAX SURR Most surround
2
1
0 Neutral
+1
+2
+3 MAX CENTRE Most centre
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam DiVA AVR200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam DiVA AVR200 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info