Manual Arcam CDS27 (page 5 of 69) (English, German, Dutch, French, Italian, Spanish)

578729

Zoom out

Zoom in

1/69

E-5E-4

English

installation

Placing the unit

< Place the CD player on a level, rm surface,

avoiding direct sunlight and sources of heat or

damp.

< Do not place the CD player on top of an

amplier or other source of heat.

< Do not place the CD player in an enclosed space

such as a bookcase or closed cabinet unless

there is good provision for ventilation. e CD

player is designed to run warm during normal

operation.

< Do not place any other component or item on

top of the CD player as this may obstruct airow

around the unit, causing the CD player to run

hot.

< Make sure the remote-control receiver (next to

the display on the front panel) is unobstructed,

or remote control will be impaired.

< Do not place your record deck on top of this

unit. Record decks are very sensitive to the noise

generated by mains power supplies which will be

heard as a background ‘hum’ if the record deck

is too close.

Power

e CD player is supplied with a moulded mains plug

already tted to the lead. Check that the plug supplied

ts your supply – should you require a new mains lead,

please contact your Arcam dealer.

If your mains supply voltage or mains plug is dierent,

please contact your Arcam dealer immediately

Push the IEC plug end of the power cable into the

socket on the back of the CD player, making sure that it

is pushed in rmly. Plug the other end of the cable into

your mains socket and, if necessary, switch the socket

on.

The remote control and trigger

inputs

e REMOTE IN input can be used to pass RC5 codes

to the CDS27 if it is installed in a position or system,

where infrared cannot be used. If this is required, please

contact your dealer for further information.

NOTE

< e remote control input requires a mono

3.5mm jack, with the tip active and the

sleeve grounded.

< e remote control signals must be in

modulated RC5 format (at 36kHz), with a

voltage level of between 5V and 12V.

e 12V TRIGGER IN input can be used to switch the

CDS27 into and out of standby. Connecting the trigger

output of your Arcam amplier (or other compatible

device), will cause the CDS27 to come out of standby

automatically when the amplier is switched on,

returning to standby when the amplier is switched

o. Please see your amplier handbook for further

information.

In normal use there is no need to make any connections

to these inputs.

e RS232 input is for optional connection to a home

automation system or computer. Various third-party

systems are available providing sophisticated control

over all your entertainment devices using touch screens

etc. Contact your dealer or installer for further details.

e technical details of the remote control protocol

are available from Arcam on request (email support@

arcam.co.uk).

Interconnect cables

We recommend the use of high-quality screened cables

that are designed for the particular application. Other

cables will have dierent impedance characteristics

that will degrade the performance of your system (for

example, do not use cabling intended for video use to

carry audio signals). All cables should be kept as short

as is practically possible.

It is good practice when connecting your equipment to

make sure that the mains power-supply cabling is kept

as far away as possible from your audio cables. Failure

to do so may result in unwanted noise in the audio

signals.

Contents

safety guidelines ��E-2

Important safety instructions �� E-2

Safety compliance �� E-2

welcome ��E-3

installation ��E-5

Placing the unit �� E-5

Power �� E-5

The remote control and trigger inputs �� E-5

Interconnect cables �� E-5

CDS27 connections ��E-6

Network connection �� E-7

USB connection �� E-7

Making audio connections �� E-7

Playable discs �� E-7

Supported Media �� E-7

basic operation ��E-8

remote control ��E-9

settings menus �� E-11

Navigating the menus �� E-11

troubleshooting �� E-12

specications �� E-13

Radio interference��E-13

Laser radiation �� E-13

software licencing �� E-14

product guarantee �� E-16

Worldwide Guarantee��E-16

Claims under guarantee ��E-16

Problems? ��E-16

On-line registration ��E-16

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam CDS27 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam CDS27 Manual

Product: