482342
63
Zoom out
Zoom in
Previous page
1/74
Next page
E-61
English
Problem Check that...
Sound only comes from some
of the speakers
<
you have an appropriate surround source selected and playing.
<
the DVD disc is encoded in the appropriate format, and the correct format
has been selected in the disc start menu of the DVD player (if applicable).
<
the DVD player has been set to output ‘bitstream’ audio on the digital
output.
<
the display window indicates that the disc you are playing is a multichannel
recording (you may need to press the INFO key several times until you get to
the ‘incoming format’ display).
<
all the speakers are correctly connected to the speaker terminals and are
secure.
<
you have not selected ‘Stereo’ as the decoding mode.
<
your speaker balance is correct.
<
you have congured the unit to include all the speakers in your system.
Unable to select Dolby Digital
or DTS decoding modes
e AVR500/AVR600/AV888 can only apply Dolby Digital and DTS decoding
to sources which have been encoded in the same format.
Check that:
<
digital source is selected and connected.
<
the source is playing appropriately encoded material.
<
the DVD disc is encoded in the appropriate format and that the correct
format has been selected in the disc start menu of the DVD player (if
applicable).
<
the DVD player has been set to output ‘bitstream’ audio on the digital output
(not PCM).
When playing a Dolby Digital
DVD, the AVR600 selects
Dolby Pro Logic
<
you have a digital connection from your DVD player.
<
sometimes Dolby Digital DVD discs contain material at either the beginning
or the end of the main movie that is not in full 5.1 format, but in two-
channel or Pro Logic decoding.
Hum on the analogue input
<
all cables are making a good connection. If necessary withdraw the cable
from the connector and plug it fully in again (turn the power o before
doing this).
<
the connections inside the source cable connector are not broken or badly
soldered.
<
if the hum originates only when one particular source component is
connected, that an aerial cable, or dish connection to this source is ground
isolated. Contact your installation contractor.
ere is radio or television
reception interference
<
where the interference is coming from. Switch o each source component in
turn, then any other equipment. Most electronic equipment does generate
low levels of interference.
<
try re-arranging cabling from the nuisance source away from other cabling.
<
ensure that the cabling used is high quality, specied for its purpose, and is
properly screened.
<
if the problem persists, contact your dealer.
Problem Check that...
e source switching changes
randomly or freezes on one
source
<
there are no static or impulse interference problems caused by nearby power
equipment switching, e.g., heating or air conditioning control. Switch the
unit o, wait ten seconds, then switch it on again to clear an operating
problem. Contact your installer if the problem returns or persists.
<
there is no direct sunlight shining on the infra-red detector behind the front
panel display.
Volume is always too loud
when I turn on
<
the ‘max on volume setting is not set too high.
When Zone2 or 3 is put into
standby, the main zone is also
switched o
<
the ‘zone standby‘ setting in the setup menu is set to LOCAL.
When a USB memory device is
connected, ‘USB’ is not shown
in the network clients list of
folders
<
a USB memory device is connected that conforms to the mass storage class.
<
a USB hub is not being used.
If les on a USB memory
device cannot be played:
<
the USB device is formatted in FAT16 or FAT32.
<
the USB device does not have multiple partitions.
<
the les are in a compatible format.
If les on a computer cannot
be played
<
the les are in a compatible format.
<
the computer is connected via a network and not USB – the AVR500/
AVR600/AV888 USB port cannot be used for a direct connection to a
computer
If you cannot connect to a
wired network
<
the Ethernet cable you are using is correctly connected between the
AVR500/AVR600/AV888 and the network hardware.
<
the network is set up for xed IP addressing and you have the AVR500/
AVR600/AV888 set to use DHCP.
<
the network is set up for DHCP and you have the AVR500/AVR600/AV888
set to use xed IP addressing.
If you cannot connect to a
favourite internet radio station
<
the station is still broadcasting or is not congested – try again later.
If the internet radio station
sound quality is poor or
broken
<
the radio station does not have a low bit rate (use the INFO key to nd this or
look on the OSD).
<
the network is not slow or congested.
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam AVR600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AVR600 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam AVR600

Arcam AVR600 User Manual - German, Dutch - 200 pages

Arcam AVR600 User Manual - Dutch - 72 pages

Arcam AVR600 User Manual - French - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info