482342
56
Zoom out
Zoom in
Previous page
1/74
Next page
E-54
Zone2 and 3 control outputs
e AVR500, AVR600 and AV888 also allow remote
control from remote zones.
Z2 IR and Z3 IR
is allows the AVR500/AVR600/AV888 to be
controlled remotely from Zone2 (or Zone3) via Infra-
red remote control. Connect a remote IR receiver in
Zone2 (or Zone3) to allow control of the AVR500/
AVR600/AV888 from these listening/viewing areas.
For more information on remote IR receivers, see ‘Z1 IR
on page 17.
TRIG Z2 and TRIG Z3
is allows the AVR500/AVR600/AV888 to remotely
switch on devices in Zone2 (or 3) when the appropriate
Zone is selected. For example you could set your
television in Zone2 to switch on when ‘Zone2’ is
selected on AVR500/AVR600/AV888.
For more information on triggers, see ‘Trigger
connectors’ on page 17. Please note that not all AV
devices have this feature, nor are triggers essential for
listening and viewing in a separate zone.
multi-room
set up
e AVR500, AVR600 and AV888 allow independent
routing and control of analogue audio, Composite and
S-Video to a separate set of equipment, typically used
for a second living space, e.g., bedroom or lounge. e
AVR600 and AV888 also allow a copy of the Zone2
analogue audio to be routed to and controlled in a third
living space, Zone3.
e connection guide on the facing page shows how the
AVR600 or AV888 is normally connected in a multi-
room installation.
Zone2
Zone2 receives only signals obtained by the AVR500,
AVR600 or AV888 from the analogue audio, Composite
and S-Video inputs. e analogue inputs are required
because there is no analogue-to-digital, digital-to-
analogue or DSP processing available for Zone2 signals
– the unit only converts video formats for Zone1.
For this reason, we recommend that in addition to any
digital connections, the Composite and/or S-Video
outputs from your source devices are connected to the
AVR500, AVR600 or AV888.
Video outputs
e Z2 S-Video and/or Composite output connectors of
the AVR500/AVR600/AV888 should be connected to
the analogue video inputs (usually labelled SVIDEO IN or
COMPOSITE VIDEO IN) of the display device in Zone2.
If you wish to make an HDMI connection to Zone 2,
you must accept the limitations of the AVR500/AVR600/
AV888 video processing system.
HDMI OUT 1 and OUT 2 both carry the same signals (as
there is only one video processing engine) and are
primarily intended for use in Zone 1. Full HDMI video
functionality in Zone 2 can only be achieved if Zone 1 is
not being used at the same time.
If Zone 1 is being used at the same time as Zone 2,
Zone 2 must follow the Zone 1 source selection if you
wish to receive HDMI signals in Zone 2. Zone 2 must
also be the same video resolution as Zone 1. If you wish
to watch a dierent source in Zone 2 than is currently
showing over HDMI in Zone 1, Zone 2 will be forced to
use the analogue video connections into and out of the
AVR500/AVR600/AV888.
Due to the complications of using HDMI in Zone 2
we recommend the use of analogue video connections
instead, particularly as it is not possible to apply audio
lip sync to Zone 2 audio to compensate for video
processing delays.
SIRIUS
AM
DAB
FM
ETHERNET
Z2 IR
IR OUT
Z1 IR
Z3 IR
rLead/rDockRS232
USB
TRIG Z1
TRIG Z2
TRIG Z3
Audio outputs
e Z2 OUT, R and L phono sockets should be connected
to the analogue audio inputs (Usually labelled
ANALOGUE AUDIO IN) of the Zone2 display device, or
to the inputs of an additional stereo power amplier in
Zone2 (for example, the Arcam P38).
Zone3 (AVR600/AV888 only)
A line-level signal from the stereo analogue audio is
available for Zone3. is is a copy of the Zone2 audio
signal, but has its own independent volume control.
Audio outputs
e Z3 OUT, R and L phono sockets should be connected
to the inputs of an additional stereo power amplier in
Zone3 (for example, the Arcam P38).
888
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam AVR600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AVR600 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam AVR600

Arcam AVR600 User Manual - German, Dutch - 200 pages

Arcam AVR600 User Manual - Dutch - 72 pages

Arcam AVR600 User Manual - French - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info