Manual Arcam AVR600 (page 46 of 74) (English)

482342

Zoom out

Zoom in

1/74

E-44

Out 1 & 2 Resolution – is setting controls the

output resolution when both HDMI outputs are used

simultaneously. is setting is only valid if Output

Switching is set to Output 1 & 2.

< e dropdown list shows all the resolutions that the

video processor can output. Resolutions that are

not supported by the connected display devices are

greyed out and cannot be selected.

< Best: sets the HDMI output to be the highest

common resolution that is supported by both

display devices.

Out 1 & 2 Frame Rate – is setting controls the

output frame rate when both HDMI outputs are used

simultaneously. is setting is only valid if Output

Switching is set to Output 1 & 2.

< e dropdown list shows all the frame rates that the

video processor can output. Frame rates that are

not supported by the connected display devices at

the above resolution are greyed out and cannot be

selected.

< Auto: sets the HDMI output to be the highest

preferred common frame rate that is supported by

both display devices for the above resolution.

<Follow Input forces the

OUT 1 & 2 frame rate to

the same as the input frame rate, regardless of the

reported capabilities of the display device.

Lipsync 1 & 2 – (Information only) Displays how much

lip sync is automatically applied to HDMI outputs

OUT 1

and OUT 2 simultaneously to compensate for video

processing delays in the attached display devices. Not all

display devices support this function.

Mode

Lists the decode and downmix options you wish to

include when cycling through the options on the MODE

button. Settings are Yes or No. e list is divided into

two sections depending on the source audio type. See

section ‘Multichannel source modes’ on page 47 for

more information on each processing a decoding mode.

ese settings are applied to all audio inputs and are

stored in memory and recalled each time the unit is

powered up.

For Stereo sources:

Dolby ProLogic –

Dolby PLIIx Movie –

Dolby PLIIx Music –

Dolby PLIIx Matrix –

Dolby PLIIx Game –

Neo:6 Cinema –

Neo:6 Music –

e rst section, ‘Stereo sources’ is the list of processing

modes you wish to make available for stereo signals

(analogue stereo, digital PCM stereo, Dolby 2.0, DTS

2.0, etc). When a stereo signal is applied, each press of

the

MODE button cycles through the processing modes

you have enabled in the ‘Stereo sources’ section. e

unprocessed Stereo option is always available for stereo

signals therefore it is not shown in the list.

For Multichannel sources:

Stereo Downmix –

Dolby Digital EX –

Dolby PLIIx Movie –

Dolby PLIIx Music –

e second section, ‘Multichannel sources’ is the list

of processing modes you wish to make available for

multichannel digital signals (any Dolby or DTS digital

stream that has more channels than stereo 2.0). When a

multichannel digital signal is applied, each press of the

MODE button cycles through the processing modes you

have enabled in the ‘Multichannel sources’ section.

Zone Settings

Lists the volume and control settings for Zone2 and

Zone3 (Zone 3 available with AVR600/AV888 only).

ese settings are applied to all audio inputs and are

stored in memory and recalled each time the unit is

powered up.

Z2 Audio Input – Selects the analogue audio to be

routed to Zone2.

Z2 Video Output – Selects the analogue video to be

routed to Zone2 for the current audio input.

Zone2 Volume – e current volume in Zone2.

Zone2 Max. Vol – Limits the maximum volume setting

the system can be turned up to in the Zone2. is is a

useful feature to prevent accidental overdriving of low

power-handling speakers, for example.

Zone2 Fixed Vol – e Zone2 volume control can be

locked at the current value for use with an external

amplier with its own volume control in Zone2.

Zone2 Max On Vol – Limits the maximum volume the

system operates in the Zone2 when it is switched on

or comes out of Standby. e system comes on at this

volume if the last used (possibly very loud) volume

exceeds this value.

Zone3 Volume – e current volume in Zone3.

Zone3 Max. Vol – Limits the maximum volume setting

the system can be turned up to in the Zone3. is is a

useful feature to prevent accidental overdriving of low

power-handling speakers (for example).

Zone3 Fixed Vol – e Zone3 volume control can be

locked at the current value for use with an external

amplier with its own volume control in Zone3.

Zone3 Max On Vol – Limits the maximum volume the

system operates in the Zone3 when it is switched on

or comes out of Standby. e system comes on at this

volume if the last used (possibly very loud) volume

exceeds this value.

Standby – When a Standby command is received by an

infra-red eye in Zone2, this setting controls which parts

of the AVR500, AVR600 or AV888 to turn on and o:

When Local Only, the Standby IR command only aects

the zone it was received in (Zone2 or Zone3).

When All O, the Standby IR command aects the

entire system in all zones.

Network

e AVR600 and AV888 are tted with a network audio

client (optional for the AVR500) which is capable of

playing internet radio stations as well as stored music

on a network storage device such as a PC, or on a USB

ash drive.

Use DHCP – Select if your network uses DHCP

<No: To assign a xed IP address manually.

<Yes: To use network parameters given by the DHCP

server.

MAC address – (Information only) e unique address

of the network card in your AVR500/AVR600/AV888.

IP Address – If not using DHCP, enter the IP address

you have assigned to the AVR500/AVR600/AV888 for

your network.

Subnet Mask – If not using DHCP, enter the subnet

mask for the AVR500/AVR600/AV888 on your network.

Gateway – If not using DHCP, enter the IP address of

the router the AVR500/AVR600/AV888 is connected to.

Primary DNS – If not using DHCP, enter the Primary

DNS IP address of your internet service provider.

Alternate DNS – If not using DHCP, enter the Secondary

DNS IP address of your internet service provider.

Use Proxy – Select if you connect to the network via a

Proxy Server.

<No: If you connect directly onto the network.

<Yes: If you connect to the network via a Proxy

Server.

Proxy Address – If connecting via a Proxy Server, enter

its IP address.

Proxy Port – If connecting via a Proxy Server, enter the

port number to which the Proxy responds.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AVR600 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam AVR600

Arcam AVR600 User Manual - German, Dutch - 200 pages

Arcam AVR600 User Manual - Dutch - 72 pages

Arcam AVR600 User Manual - French - 200 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam AVR600 Manual

Product: