482342
33
Zoom out
Zoom in
Previous page
1/74
Next page
E-31
English
AMP
AMP Device Mode
e
A
Device Mode button congures the CR102
to control the AVR500/AVR600/AV888. Pressing this
button does not aect the currently selected input on the
AVR500/AVR600/AV888.
IMPORTANT: e CR102 must also be in
AMP Device
Mode to control the following sources: PHONO, MCH
(multichannel analogue), AUX, NET (optional network
audio), USB, IPOD (for use with the optional Arcam
rLead or rDock).
However to control the internal Tuner in the AVR500/
AVR600 (AM/FM/DAB or Sirius if tted), the CR102
must rst be in
TUN Device Mode (see later).
e functionality of the CR102 is context sensitive for
the internal sources and is described in the following
table.
P
Single press – Toggles AVR500/AVR600/
AV888 power between standby and on
in the current zone (zone in which the
command is received).
Press and hold – Forces all AVR500/
AVR600/AV888 zones into standby,
regardless of which zone the command was
received in.
0
9
e number keys can be used for source
selection (without changing the CR102
Device Mode). Alternatively the Device
Mode buttons can also be used with the
SHIFT key.
0
SAT (satellite) input
1
PHONO input
2
AV input
3
TUNER input
4
DVD input
5
TAPE input
6
VCR input
7
CD input
8
AUX (front panel) input
9
MCH (multichannel) input
PHONO
E
Selects Tape input on the AVR500/AVR600/
AV888
SHIFT +
E
selects PHONO input on the
AVR600/AV888
RPT
r
(for
IPOD and NET sources)
S
Modies many keys (see individual key
descriptions below).
AUX
H
Selects
MCH (multichannel) input on the
AVR500/AVR600/AV888
SHIFT +
H
selects AUX input on the
AVR500/AVR600/AV888
OK
Navigate menus
OK conrms a setting (equivalent to ‘Enter
or ‘Select’ on some remote controls)
Press and hold
OK to force the analogue
and digital video outputs to the default
resolution: 480i (525-line NTSC).
SHIFT +
<
decreases the picture resolution.
SHIFT +
>
increases the picture resolution.
SHIFT +
'
turns current zone (in which
command is received) on
SHIFT +
,
turns current zone (in which
command is received) o.
NET
e
Selects
IPOD input on the AVR500/AVR500/
AVR600/AV888
SHIFT +
e
selects network (NET) internal
input on the AVR500/AVR600/AV888
(where tted).
M
Cycles through the available surround and
downmix modes.
U
Displays the AVR500/AVR600/AV888 setup
menu on the On Screen Display (see page
34).
D
Cycles through the front panel display’s
brightness options
@
Toggles the mute function of the AVR500/
AVR600/AV888
] [
(track control for
IPOD and NET sources)
SHIFT +
[
Follow Zone1 source.
When the command is received in Zone2
or Zone3, the source for that zone follows
whatever input source is selected in Zone1
- +
Decrease () and increase (+) AVR500/
AVR500/AVR600/AV888 volume
DIRECT
)
Stereo direct on/o. Provides a direct
analogue path from the analogue inputs to
the le and right front outputs. Switches o
any surround processing modes and shuts
down the DSP circuits for the best stereo
sound quality.
EQ
$
Displays the room EQ settings menu
EFFECT
&
(for
IPOD and NET sources)
BASS
(
Calls up a pop-up (and front screen) to
adjust the bass setting for a particular input.
TRIm
!
Brings up the speaker trim menu.
Use the
B
,
C
,
D
and
E
navigation
buttons. Press TRIM again to exit the speaker
trim menu.
As this is a temporary adjustment, these
additional trim levels are reset to zero when
the unit is turned o or put into standby,
but are retained if the selected input is
changed. ese temporary trim levels are
independent of the speaker levels found in
the setup menu.
SyNC
#
Delays may be introduced into the video
signal by video processing which causes
a mismatch between the audio and video
timing. You will notice this by speech sound
being out of synchronization with the lip
movements in the video.
To compensate for this, you can adjust the
lip sync delay. Press the
SYNC button and
use the
D
and
E
navigation buttons. Press
again to exit the lip sync trim menu.
SUB
%
Brings up the subwoofer trim menu. Use
the
D
and
E
navigation buttons. Press SUB
again to exit the sub trim menu
TREBLE
h
Calls up a pop-up (and front screen) to
adjust the treble setting for a particular
input.
FAV+
u
(for
IPOD and NET sources)
FAV-
t
(for
IPOD and NET sources)
HOmE
o
(for
IPOD and NET sources)
INFO
b
Cycles through the information displayed
on the lower le portion of the front panel
display.
iPod commands
e iPod interface is selected by pressing
e
in AMP
Device Mode on the CR102. When connected to an
iPod via an optional rLead/rDock, the keys below are
used to navigate music les in AMP Device Mode.
OK
Navigate the files on screen.
OK selects/play the highlighted file.
RPT
r
Toggles random (shuffle) play of the playlist
on and off.
SHIFT +
r
cycles through the repeat options
] [
Selects the previous/next track in the
current playlist
$
Begins or resumes playback at the currently
highlighted track
&
Toggles pause and playback of the current
track
#
Stops playback
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam AVR600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AVR600 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam AVR600

Arcam AVR600 User Manual - German, Dutch - 200 pages

Arcam AVR600 User Manual - Dutch - 72 pages

Arcam AVR600 User Manual - French - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info