482343
45
Zoom out
Zoom in
Previous page
1/74
Next page
E-43
English
Video Inputs
Settings to optionally assign a video source to each of
the normally audio-only inputs.
ese settings are stored in memory and recalled each
time the unit is powered up.
Video Input Tape –
Video Input CD –
Video Input Aux –
Video Input AM / FM
Video Input Phono –
Video Input MCH –
Video Input iPod –
Video Input Net –
Video In Digital Radio –
e default for each of the audio inputs is ‘None,
however for example you could associate the satellite
Sat’ video with AM, FM and Digital Radio audio if you
wished. is way you could listen to the FM or AM or
Digital Radio commentary of a sports game but have the
pictures from the satellite coverage.
Video Outputs
e settings in this menu control the output resolution
from the video processor in the unit as well as the
operation of the two HDMI outputs.
ese settings are applied to all video inputs and are
stored in memory and recalled each time the unit is
powered up.
NOTE
Important points to remember:
For analogue outputs
e analogue output resolution should be chosen
carefully; Composite and S-Video connections can
only carry 480i (525-line NTSC) or 576i (625-line
PAL) signals. If an output resolution higher than this
is chosen in Out 1 Resolution, the Composite and
S-Video main zone outputs will be disabled.
You should also set the frame rate (50Hz Interlaced
for PAL, 60Hz Interlaced for NTSC) and the
aspect ratio (4:3 standard or 16:9 widescreen) to
match your display device. Note that S-Video and
Composite can only carry Interlaced video. If you
select Progressive analogue video, Zone1 S-Video
and Composite outputs will be disabled.
For HDMI outputs
e output resolution, frame rate and display
aspect ratio can be automatically determined by the
unit. Alternatively these settings can be manually
selected. If you have two HDMI display devices
connected, you can also congure which of the two
HDMI outputs takes priority.
Zone1 OSDSelects whether the main zone pop-up
OSD messages are On or O. It is stored in memory and
recalled each time the unit is powered up.
< When On, all user adjustments that are made during
the general use of the unit are displayed on screen
as well as the front panel display. is includes the
adjustment of volume, subwoofer level, lip sync, tone
controls, etc. It is stored in memory and recalled
each time the unit is powered up.
< When O, the above user adjustments will not
appear on screen, only on the front panel display.
is leaves the picture on your display device clear
of pop-up text. However, regardless of this setting
the Setup menus are always displayed on screen.
Analogue Outputis setting controls the output
resolution of the analogue video outputs of Zone1.
is applies to all Zone1 analogue video outputs:
Component, S-Video and Composite. is setting is
only valid if neither of the HDMI outputs
OUT 1 or OUT 2
are being used at the time. See ‘Important points to
remember’ above regarding analogue resolutions.
e dropdown list shows all the resolutions that the
units video processor can output.
Analogue Frame Rate – is setting controls the output
frame rate of the analogue video outputs of Zone1.
is applies to all Zone1 analogue video outputs:
Component, S-Video and Composite. is setting is
only valid if neither of the HDMI outputs
OUT 1 or OUT 2
are being used at the time. See the Note ‘Important
points to remember’ regarding analogue frame rates.
Display Type – Set the aspect ratio of your display
device; 4:3 standard or 16:9 widescreen.
Output Switchingis setting controls the operation
of the two HDMI outputs.
<Auto-Priority Out 1/Out 2 senses which display
device is turned on and gives priority to the named
output (
OUT 1 or OUT 2) if both display devices are on
at the same time. When both display devices are on
at the same time, the output with the highest priority
is used to congure the settings of the units video
processor.
< Output 1 or Output 2: forces only the named HDMI
output to be enabled.
< Output 1 & 2: enables both HDMI outputs
simultaneously. In order to do this however, the
settings of the units video processor are reduced
down to the highest common set that can be
supported by both display devices.
Out 1 Resolution – is setting controls the output
resolution of HDMI output
OUT 1. is setting is only
valid if HDMI output OUT 1 is the only active HDMI
output at the time.
<e dropdown list shows all the resolutions that the
video processor can output. Resolutions that are
not supported by the connected display device are
greyed out and cannot be selected.
< Preferred: sets the
OUT 1 resolution to be the
preferred resolution that is requested by the display
device. is is oen the highest resolution the
display device can receive.
Out 1 Frame Rate – is setting controls the output
frame rate of HDMI output
OUT 1. is setting is only
valid if HDMI output OUT 1 is the only active HDMI
output at the time.
<e dropdown list shows all the frame rates that the
video processor can output. Frame rates that are
not supported by the connected display device at
the above resolution are greyed out and cannot be
selected.
<Auto sets the
OUT 1 frame rate to be the preferred
frame rate that is requested by the display device for
the currently used resolution.
<Follow Input forces the
OUT 1 frame rate to the same
as the input frame rate, regardless of the reported
capabilities of the display device.
Lipsync 1 – (Information only) Displays how much lip
sync is automatically applied to HDMI output
OUT 1 to
compensate for video processing delays in the attached
display device. Not all display devices support this
function.
Out 2 Resolution – is setting controls the output
resolution of HDMI output
OUT 2. is setting is only
valid if HDMI output OUT 2 is the only active HDMI
output at the time.
< e dropdown list shows all the resolutions that the
AVR500, AVR600 or AV888 video processor can
output. Resolutions that are not supported by the
connected display device are greyed out and cannot
be selected.
< Preferred: sets the
OUT 2 resolution to be the
preferred resolution that is requested by the display
device. is is oen the highest resolution the
display device can receive.
Out 2 Frame Rate – is setting controls the output
frame rate of HDMI output
OUT 2. is setting is only
valid if HDMI output OUT 2 is the only active HDMI
output at the time.
< e dropdown list shows all the frame rates that the
video processor can output. Frame rates that are
not supported by the connected display device at
the above resolution are greyed out and cannot be
selected.
< Auto: sets the
OUT 2 frame rate to be the preferred
frame rate that is requested by the display device for
the currently used resolution.
<Follow Input forces the
OUT 2 frame rate to the same
as the input frame rate, regardless of the reported
capabilities of the display device.
Lipsync 2 – (Information only) Displays how much lip
sync is automatically applied to HDMI output
OUT 2 to
compensate for video processing delays in the attached
display device. Not all display devices support this
function.
Progressive scan playback
e AVR500, AVR600 and AV888
can support 1080p, 24 frames per
second source materials. To enjoy
24p playback both the source device (e.g., a Blu-ray
disc player) and the display device (e.g. a TV or
projector) must be capable of supporting 24p.
To enjoy 24p playback, set the Video Source to
HDMI in the Input Cong. menu, and set the
Output resolution to 1080p (i.e. not to Preferred)
in the Video Outputs menu. Also, ensure that the
Frame Rate is set to Auto.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam AV888 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AV888 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam AV888

Arcam AV888 User Manual - German, Dutch - 200 pages

Arcam AV888 User Manual - Dutch - 72 pages

Arcam AV888 User Manual - French - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info