482343
13
Zoom out
Zoom in
Previous page
1/74
Next page
E-11
English
Trigger connectors
e trigger connectors (TRIG Z1, TRIG Z2 and TRIG Z3)
provide an electrical signal whenever the amplier is
switched on and the relevant zone enabled.
e trigger signal can be used
to switch on and o compatible
pieces of home entertainment
equipment, for example, you
could set up a trigger to turn on
your television and DVD player
whenever the unit was switched
on.
ere are three trigger output
sockets on the unit, each capable
of outputting a 12V, 70mA
switching signal. e socket
is designed for mono 3.5mm jacks: tip is the trigger
output, sleeve is ground.
tip: Trigger output
sleeve: Ground
TRIG Z1
Use for remotely turning on and o power amps or
source equipment for Zone1. On = 12V, O = 0V.
TRIG Z2
Use for remotely turning on and o power amps or
source equipment for Zone2. On = 12V, O = 0V.
Infra-red (IR) connectors
e infra-red inputs (Z1 IR, Z2 IR
and Z3 IR) allow the connection of
external IR receivers, either when
the units front panel IR receiver is
fully or partially obstructed or to
allow the use of a remote control
in Zone2 or Zone3.
ere are three IR inputs on the
unit, each designed for stereo or
mono 3.5mm jacks. Tip is the
modulated signal, sleeve is ground.
tip: Modulated signal
sleeve: Ground
Z1 IR
is input is intended for use with a local IR receiver
when the front panel of the unit is blocked.
Connecting an IR receiver to
Z1 IR will disable to front
panel IR receiver to prevent problems with multiple
commands if the front panel IR receiver is only partially
obstructed.
Z2 IR
is input is intended for use with an IR receiver in
Zone2 to allow remote control of the unit from a second
room.
SIRIUS
AM
DAB
FM
ETHERNET
Z2 IR
IR OUT
Z1 IR
Z3 IR
rLead/rDock
RS232
USB
TRIG Z1
TRIG Z2
TRIG Z3
SIRIUS
AM
DAB
FM
ETHERNET
TRIG Z1
TRIG Z2
TRIG Z3
rLead/rDock
RS232
USB
Z2 IR
IR OUT
Z1 IR
Z3 IR
Z3 IR
is input is intended for use with an IR receiver in
Zone3 to allow remote control of the unit from a third
room.
IR OUT
is output is an electrical combination of the Z1 (or
front panel) + Z2 + Z3 infra-red signals above. It can be
used to drive external IR emitters or can be connected
directly to other Arcam equipment which have an IR
input. is function can be useful as an IR ‘repeater
so that someone in any of the zones can control the
functions of a CD player in the main zone, for example.
Tip is the modulated electrical IR signal, sleeve is
ground.
A supplier of infra-red receivers and emitter accessories
and systems is Xantech. See www.xantech.com for
more information, or ask your Arcam dealer.
NOTE
e IR inputs on the unit are designed for
modulated signals. If the external IR receiver
demodulates the IR signal, it will not work. Also the
unit does not provide power for external receivers
on the IR jack, therefore an external power source
will be required.
TRIG Z3
Use for remotely turning on and o power amps or
source equipment for Zone3. On = 12V, O = 0V.
NOTE
Sockets with the prex ‘Z2’ or ‘Z3’ refer to
connections used in multi-room installation. For
more information on these connectors, see page 54.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam AV888 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AV888 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam AV888

Arcam AV888 User Manual - German, Dutch - 200 pages

Arcam AV888 User Manual - Dutch - 72 pages

Arcam AV888 User Manual - French - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info