471451
40
Zoom out
Zoom in
Previous page
1/46
Next page
38-EN
ALPINE DHA-S690 68-09359Z17-A (EN)
Installation
CAUTION
Be careful that the vehicle’s cords do not touch
the DHA-S690.
If the cords are in contact with the DHA-S690,
their sheaths may be damaged due to vibrations
generated while the vehicle is running, resulting
in short-circuits. Leave enough space when
routing wires to prevent contact between the
vehicle’s wires and the DHA-S690.
To prevent external noise from entering the audio system.
Locate the unit and route the leads at least 10 cm away from the
car harness.
•Keep the battery power leads as far away from other leads as
possible.
Connect the ground lead securely to a bare metal spot (remove any
paint, dirt or grease if necessary) of the car chassis.
If you add an optional noise suppressor, connect it as far away
from the unit as possible. Your Alpine dealer carries various noise
suppressors. Contact them for further information.
•Your Alpine dealer knows best about noise prevention measures so
consult your dealer for further information.
Remove the shipping keys.
Three keys are mounted to the DHA-S690’s bottom panel
to protect the product during transportation. Be sure to
remove these keys before installing the DHA-S690. So as
not to lose the keys, store them in the special plastic
pouch provided with the DHA-S690 and cover the key
holes with the included dust-prevention seals.
•The eject operation cannot be performed if the keys are mounted
when the power is turned on. Turn the power off, then remove the
keys.
1
Mounting strap
Protective plastic bag
for shipping keys
Lock Keys
Install the L-shaped bracket.
1 Determine the position and angle of installation.
2 Referring to step 3, change the position of the springs
according to the angle of installation.
3 Install the L-shaped bracket 2 according to the angle of
installation. Fasten it in place using the double washer
screws (M4x8) 6.
L Example of Installation Using Attached L-
shaped bracket.
6
5
3
4
2
1
6
5
3
4
2
1
L-shaped
bracket holes
H
V
90°
H
V
90°
Vertical
Horizontal
Use any pair of holes
5 or 6 and fix with
4 screws (2 screws ×
both sides).
Use any pair of holes
1, 5 or 6 and fix
with 4 screws
(2 screws × both sides).
Change the position of the springs.
With this product, the positions of the built-in anti-vibration
springs must be changed according to the angle of
installation. The product will not provide the regular
resistance to vibration if the anti-vibration springs are not
in the correct positions or if the left and right springs are in
different positions.
The anti-vibration springs can be placed at one of five
angles.
The springs are set to the “H” angle upon shipment from
the factory. To change this angle, follow the instructions
given below.
1 Remove the covers provided at both left and right sides of
the unit by pressing claws of the covers in the direction
shown by the arrow.
2 Change the position of the springs
using a finger.
3 Mount the covers at the left and
right sides as they were attached
originally.
Install the unit only at a horizontal or vertical angle. If the unit is
diagonally installed, malfunction may result.
2
3
H
V
R
COVER
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Apine DHA-S690 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Apine DHA-S690 in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info