Manual Apa 16622 (page 11 of 32) (English, German, Dutch, French, Italian)

807550

Zoom out

Zoom in

1/32

6.5.1 SELECTING THE CHARGING PROGRAMME

To start the charging process, press the selection switch

for the charging programme (Position 3 in the overview)

until the charging programme you want is set. If no charging

programme is set, the charging process will not start. The

most recently set charging programme is saved and can

simply be started by pressing the selection switch once the

next time you use the charger. The charging programmes

are switched in the following order (see also Figure 3 in the

overview):

1. 6 V mode

2. 6 V winter mode

3. 12 V motorbike mode

4. 12 V motorbike winter mode

5. 12 V car mode

6. 12 V car winter mode

6.4 CONNECTING THE BATTERY CHARGER

6.4.1 CONNECTING THE ADAPTER CHARGING

CABLE WITH POLE CALLIPERS

Make sure that the charger is not connected to

the power socket and that the adapter charging

cable is not connected to the battery charger.

Make sure that the charger is not connected to

the power socket and that the adapter charging

cable is not connected to the battery charger.

If the red control lamp „ERROR“ (Position 4 in

the overview) lights up, and the error message

„Er 1“ ashes on the display, the charging cables

have been connected incorrectly. Remove the

pole callipers/eyes from the battery poles and

connect them correctly.

Always connect the red plus cable (+) to the positive pole

of the battery rst. Subsequently, connect the black minus

cable (-) to the negative pole of the battery. If you charge

the battery in situ, connect the black negative cable (-) to

the car body (exposed part), far away from the battery, the

carburettor and fuel lines. Always maintain this sequence.

6.4.2 CONNECTING THE ADAPTER CHARGING

CABLE WITH EYES

Attach the eye of the red plus cable to the plus connection

cable of your vehicle battery, e.g. the screws of the pole ter-

minal. Attach the eye of the black minus cable to the earth

connection cable (minus cable) of your battery. Lay the ca-

ble so that it is free from bends and tensions. It may not be

attached in the vicinity of hot or rotating parts of the motor.

The connection plug may not get wet.

6.5 CHARGING THE BATTERY

Connect the adapter charging cable to the battery charger.

Now connect the mains connection cable (Position 5 in

the overview) of the battery charger to the power socket.

Now, the green „OPERATION“ control lamp (Position 2 in the

overview) lights up. The background illumination of the

display (Position 1 in the overview) is activated. In the

display, the battery voltage (Position 18 in the overview)

and the symbol for the operating display (Position 19 in the

overview) are shown.

CAUTION

After starting the charging process, the charging program-

me can no longer be modied. If you wish to use a program-

me that diers from the one set, pull the plug of the charger

and disconnect the battery from the charger (see section

6.6). Wait about 10 seconds until the display goes dark and

then proceed according to section 6.5.1 and set the correct

charging programme.

Depending on the charging state of the battery, the device

adapts the charging current in order to best charge the

connected battery. The specied maximum charging cur-

rent is only used during the main charging phase. Shortly

before the full charging capacity is achieved, the device

switches to a lower charging current. This ensures that the

battery is gently and optimally charged to full capacity.

The animated battery symbol (Position 17 in the overview)

as shown in the display indicates that the battery is being

charged.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16622 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3.89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Apa 16622 Manual

Product: