Manual Angelcare AC401 (page 6 of 16) (English)

537056

Zoom out

Zoom in

1/16

Step 5: Changing Channels

The Angelcare Monitor has 8 manually

selectable channels. If the transmission is

not clear or you experience interference the

channel can be changed as follows:

1. Turn both units ON.

2. Press and hold the SELECT button.

3. The current channel will be shown on the

Parent Unit display.

4. Change the channel with the ARROWS UP

or DOWN.

5. Press the SELECT button again to conﬁrm

the channel.

ALWAYS keep at least 3 metres distance

between the Parent Unit and the Nursery

Unit to avoid feedback (loud whistling

noise) between the units.

Step 6: Testing your Monitor

1. TEST YOUR MONITOR TO DETECT

MOVEMENT

1a. Make sure the Sensor Pad is installed

correctly and turn both units ON.

1b. Gently move your hand over the mattress

to simulate your baby’s movements.

Note: The movement alarm will sound if no

movement is detected within 20 seconds.

1c. Once movement is detected the green

PENDULUM light will ﬂash on the Nursery

Unit and the PENDULUM icon on the

Parent Unit screen will swing.

1d. After approx. 1 minute remove your hand

from the mattress. Do not lean against

the baby’s bed!

2. STOPPING THE ALARM

There are 2 ways of stopping the alarm once

it is sounding:

a. Turn off the nursery unit

b. Press any key on the parent unit (except

the ON OFF button). This will put the

monitor on HOLD. To deactivate the HOLD

function press and hold the down arrow

for 2 seconds. (See Other Functions

Section).

3. THE 4 CORNER TEST

Follow the same process for all 4 corners of

the mattress to ensure that the SensorPad is

picking up movements from all corners of the

mattress. If the monitor does not alarm after

20 seconds once you have taken you hand off

the mattress, the SensorPad may be detecting

other movements such as a cot mobile, a fan,

or simply the cot being touched or leant on.

If the monitor does alarm during this testing,

this could indicate that the sensitivity of the

sensor pad may need adjusting. (See

Adjusting the Sensitivity Setting).

Step 7: Adjusting the Sensitivity Settings

The Standard Setting for the Sensitivity is

Level 3. (The Sensitivity Dial on the back

of the Nursery Unit will be pre-set to Level

3. This is suitable for most bed sizes and

types of mattress. Do not Adjust unless

necessary. By increasing the sensitivity

the Sensor Pad will cover a larger area. It

could also detect vibrations from outside the

baby’s bed (i.e. cot mobiles or fans), or other

movements. It is important to ﬁnd the right

balance for your situation, to ensure optimum

performance of the sensor pad. Reducing

the sensitivity can be useful if the sensor

pad is picking up external movements. For

example a cot placed right next to an adults

bed could be picking up the movements from

the adults. In this instance you may need to

reduce the sensitivity. We recommend only

moving the Sensitivity Adjustment Dial by half

a notch and repeating the ‘4 Corner Test’, as

described above. Try this new setting for a

few days. If you need to further increase or

decrease the sensitivity please do this by a

further ½ notch and re-test.

Step 4: Establishing connection between the Parent Unit and the Nursery Unit

Once you have completed Steps 1, 2 & 3, turn

your Parent Unit on by pressing and holding

the Power button. Turn the Nursery Unit on by

pushing up the left wing to the ON position.

You will see the Channel Number appear and

after a few seconds this will change to the

temperature reading of the baby’s room.

AC401 DELUXE

1. Install the baby monitor according to the

instructions with one of the Parent Units.

This Parent Unit and Nursery Unit should

connect automatically. If this is not the

case, please follow the reconnecting

procedure. Your baby monitor is now ready

for use with one Parent Unit. If you want to

connect the 2nd Parent Unit, please go to

Step 2.

2. Keep the ﬁrst Parent Unit and Nursery Unit

turned ON and then turn on the 2nd Parent

Unit, which should also connect

automatically. If this is not the case, please

follow the reconnecting procedure. Once

both Parent Units are connected to the

Nursery Unit your baby monitor is ready

for use.

3. All monitor settings can be changed from

both Parent Units (according to the

Instruction Manual). The new settings will

automatically be activated on both

Parent Units.

SWITCHING ON

The connection between the Parent and

Nursery Unit is automatically established

every time both units are ON.

RECONNECTION PROCEDURE

Should connection not be automatically

established when you turn on both units

please follow the reconnection procedure on

the right:

1. Turn both units OFF.

2. Turn ON the Parent Unit, then press and

hold the MENU button until a beep

sounds and the OUT OF RANGE indicator

starts ﬂashing.

3. Turn ON the Nursery Unit, then press and

hold the PAIRING button on the front of

the Nursery Unit until a beep sounds and

the TIC light ﬂashes (see PART 1, Step

1a).

4. The Parent Unit will show the channel

number, which will be replaced by the

standard menu after a few seconds.

NOTE

If the Parent Unit is turned ON but the

Nursery Unit is OFF, the Parent Unit will

double beep for 1 minute and then turn

itself off as it cannot locate the Nursery

Unit. By turning the Nursery Unit on again

this will re-establish connection and the

monitor is ready for use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC401 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Angelcare AC401

Angelcare AC401 User Manual - German, Dutch, Danish, French, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 87 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Angelcare AC401 Manual

Product: