Manual Angelcare AC315 (page 3 of 68) (English, French, Spanish)

681986

Zoom out

Zoom in

1/68

26. DO NOT store this product, or the batteries provided with or identiﬁed for

use with this product, in high-temperature & high humidity environments and

avoid direct sunlight.

IMPORTANT SAFETY

INSTRUCTIONS

27. is monitor uses public airwaves to transmit signals. e Parent Unit may

pick up signals or interference from other nursery monitors in your area. Your

monitor may even be picked up by other households. To protect your privacy, make

sure both units are turned OFF when not in use. If you experience interference,

change the channel on both units.

28. Power cord protection - Protect the Sensor Pad, cord and Adapter’s

power cord from being walked on or pinched by furniture or other items

– Power supply cords should be routed so that they are not likely to be walked on

or pinched by items upon or against them, paying particular attention to cords and

plugs, convenience receptacle, and the point where they exit from the product. e

socket outlet shall be installed near the equipment and shall be easily accessible.

Make sure to plug the adapter to the socket outlet nearest to the equipment

and that is easily accessible. To disconnect from mains, unplug the adapter.

29. Only use attachments/accessories and replacement parts speciﬁed

by the manufacturer. Any mounting of the product should follow the

manufacturer’s instructions.

• DO NOT position this product on an unstable cart, stand, tripod, bracket

or table. e product may fall, causing serious injury to a child or adult and

serious damage to the product.

• Use ONLY with a cart, stand, tripod, bracket or table recommended by the

manufacturer or sold with the product.

• Be sure replacement parts are supplied by Angelcare and have the same

characteristics as original part. Unauthorised substitution may result in ﬁre,

electric shock or ﬁre.

30. Unplug this appliance during lightning storms or when not used

for long periods of time

31. Servicing - DO NOT attempt to service this product yourself as

opening or removing covers (except battery door) may expose you to

dangerous voltage or other hazards.

32. Power Supply – see Technical Speciﬁcation within this guide.

33. Overloading - DO NOT overload wall outlets, extension cords or

integral convenience receptacles as this can result in a risk of ﬁre or

electric shock.

34. Camera Unit Antenna - e antenna used for this transmitter must be

installed to provide a separation distance of at least 8’’ (20 cm) from all persons

and must not be collocated or operating in conjunction with any other antenna

or transmitter.

35. Cleaning - Disconnect all units before cleaning. DO NOT immerse in water

any part of the monitor. Clean only with dry cloth.

36. Sensor Pad –

• Vibration Source/interference - When the Sensor Pad is in use, DO

NOT use a crib mobile, other crib accessories that may produce vibrations.

Other sources of vibrations may include fans, washing machines, loud music,

etc. ese sources of vibration may interfere with the performance of your

Angelcare® monitor and the alarm will not sound if it continues to detect any

movement other than your baby’s. Be sure all vibration sources are eliminated

before using the monitor.

• If your crib does not have a solid, stationary, completely ﬂat, ﬁrm surface

including a spring or slat base, place a hard board between the crib base and

the Sensor Pad, to ensure correct operation. e hardboard support must

measure at least 33 x 33 cm (13” x 13”) and 6 mm (1/4”) thick. is hardboard

support must be larger than the Sensor Pad surface area.

• e Sensor Pad functions with any size and type of mattress except memory-

foam mattresses, hollow frame mattresses and water beds. e hardboard

maintains a constant pressure on the Sensor Pad, enabling it to detect the

baby’s movements even when the baby is at the edges of the crib.

• e sensor pad is made of plastic and does not permit the air to

circulate. erefore, mildew build up could develop underneath the mattress

in the sensor pad area. We suggest rotating the mattress regularly to prevent

any mildew.

37. False alarms may happen for several reasons:

• Camera Unit has not been turned OFF after you have removed your baby

from the crib.

• Sensor Pad has not been placed under the mattress properly. Be sure the

Sensor Pad is on a ﬂat, ﬁrm surface with the printed side facing up.

• e sensitivity level may also need to be adjusted. Refer to User’s Guide.

Always be sure to immediately check on baby whenever an alarm sounds.

WARNINGS

38. Modiﬁcations not authorized by the manufacturer may void users authority

to operate this device.

38.1 NOTE: is equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. ese limits

are designed to provide reasonable protection against harmful interference

in a residential installation. is equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

38.2 However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment

OFF and ON, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

diﬀerent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

38.3 is device complies with the part 15 of the FCC Rules and the Industry

Canada license - exempt RSS standards(s). Operation is subject to the

following two conditions:

(1) is device may not cause harmful interference, and

(2) is device must accept any interference received, including interference

that may cause undesired operation.

IC Warning :

39. is device complies with industry Canada RSS standard(s). Operation is

subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including inferences that may

cause undesired operation of the device.

39.1 Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

FCC AND IC REGULATIONS

RF radiation exposure statement

e Nursery Unit complies with FCC RF radiation exposure limits set

forth for an uncontrolled environment.

Caution: To maintain the compliance with the FCC’s and Industry

Canada’s RF exposure guideline, install the Nursery Unit at least 7.9”

(20 cm) from ALL persons. e transmitter of this device must not

be co-located or operating in conjunction with any other antenna

or transmitter.

Industry Canada

is product meets the applicable Industry Canada technical

speciﬁcations.

CAN ICES-3 (B)/NMB-3 (B)

247AC_Manuel_AC315_NA_m3.indd 3 18-03-02 16:10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC315 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 11,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Angelcare AC315

Angelcare AC315 Quick start guide - English - 14 pages

Angelcare AC315 User Manual - English - 30 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Angelcare AC315 Manual

Product: